JEC9536ADW Jenn-Air Cooktop - Instructions

Ok this is a glasstop jenn air cce3531b, 5 burners, 11 years old. I am computer data entry employee and 56 years old. I have never done repairs myself in the past but decided to try. I ordered a new burner and indicator light as I wasnt sure which to replace. I found the main breaker and shut it off. I lifted the stovetop out of the counter opening by pushing it through the bottom and placed it on the counter with a towel under it, I had plenty of room to work so that was very easy. I used a nutdriver set to remove 12 screws and lifted off the top very carefully and placed it in the other room , since I had to repair unit thought I would also clean and replace the foam tape around the perimeter of the glasstop. Ok now I unscrewed 4 more screws with the nutdriver and replaced the indicator light, that took about 6 minutes so far. Then I turned the breaker back on and tested and it did not work. Turned breaker back off ,now I replaced the burner by lifting it out of the opening very easily, unscrewed with philips screwdriver 2 screws and the new burner was exactly the same as the existing one so I just slid the old connections off one at a time and replaced them as I went along onto the new burner, screwed it back into place and turned the breaker on and tested it and it worked. I now turned the breaker back off and took off the old foam tape from the glasstop and replaced with new, fit it back onto the base and screwed the 12 screws back in and placed it back into the counter opening and turned breaker back on and now all is fixed and I saved $100 dollars in labor fees. This took 35 minutes and was easy for me. Thanks you partselect

Removed 8 screws of retainer holding glass top to box.. Pulled 5 knobs and glass top and set aside. Popped 2 retaining clips holding burner , removed them and transferred to new burner (#12 and #48 position). Used wide blade screwdriver to facilitate removing terminals from old burner and attached terminals to new burner.Popped retaining clips into crossbeam, put glass top on and 8 screws back into retainer. Works great.

First I reviewed a video on YouTube by this site. Even though the range on the video was not the same as mind, it gave me an idea on what to do. I proceeded to pull the rang out from the wall and disconnected the power plug. Next I removed two screws from the back located on the left and used a flat blade screw driver to depress two brackets on the front to release the glass top panel. I unplugged the wiring harness and disconnected the grounding wire and took the glass panel off and laid it upside down on the kitchen table. I removed the old heating element first by unplugging the wiring and removing the brackets that held it in place. Installed the new one, plugged in all wirings, brackets, screws and replace the top back on the stove.

The repair was very easy. There were 3 screws under the front lip which had to be removed. This allowed the smooth glass top to be removed, tilt and pull forward. This exposed the burners and the unit I purchased was a direct replacemt for the burnt unit. All I had to do was remove the electrical clips from the old unit and put them on the new unit. There were 3 spring elements, each with 2 screws, which held the unit in place.

My grandson, age 15 did the replacement. Now, how easy is that!

Simply replaced old switch with new one. Was very easy to do.

Important to unplug the appliance first. There were two screws which were at the top opening of the oven. They were a bit obscure, but with a bit a searching, I was able to find them. After removing those two screws, the entire top lifted up. There were four screws from the bottom of that assembly which were easy to find, and once removed, the top lifted of easily. I found it easier to remove the two power lines with two easy disconnects, this made it easier to work on the assembly. The element itself was held down by two simple clamps which required no tools. There were four easy to remove wires, and the element came right off. Simply reversing the process put it right back together, plug it in, and back to cooking again.

I took the old knob off, got needle nose pliers to get the small steel sleeve off the post, and put the new knob on. The knob had a number on the underside, but it is not the part number. Part Select's picture showed the number, so I knew it was the right part.

Our cooktop is about 9 years old. Great appliance, but poor engineering/design choice to have aluminum knobs with plastic knob shafts, that almost every time the burner gets turned on, the plastic shaft gets stressed and they crack, rendering them useless over time. I replaced all five (5), for about $80 delivered, since I got tired of repairing them. I did see a very helpful post from a guy in Arizona (thanks if you're reading this) whose daughter glued the shafts inside and out, and then wrapped them in wire. I did the same thing with my spares (I have about 7 now, after replacing one or two over the years), as I took the metal sleeve out of the middle, glued them inside and out, and used small plastic wire ties to close them up tight, then putting the metal insert back inside. After the glue dried, I snipped off the end of the wire tie. It worked great! Thanks, Tom D., from outside Boston, MA.

After unit dried I turned top back on and everything worked but right front control and no fan. I disconnected power, removed BX whip at junction box, took top out, flipped over and removed screws around side , lifted up about 4" disconnected fan laid cover back over BX. looked at right front control and saw circuit board and black all around switch area got numbers put together and ordered part. I talked to about 5 other places and didn't have a clue or part was not available. The woman I talked to knew her stuff and asked all the right questions because there was no part names or list other than right front control.

Turned off circuit breaker.Removed cooktop from counter top. Used small knife to break silicon seal. Removed glass top from pan by removing retaining screws.The removal of the old part required removal of a nut on the switch shaft which was not obvious . This required the needle nose . Otherwise the replacement was simply exchangeing the wires.

Removed module replaced radiant element very easy repair.

I actually did it manually. It was fast and easy.

Simple repair to replace stripped out knob. More importantly we ordered the part over Christmas and it arrived within 2 or 3 days

Only hitch I experienced was identifying the correct replacement. The original diagram presented the accurate shape of the element my range required. However a different shaped element was displayed when I noted my unit is a series 12 serial number. I ordered it (with reservations) and as it turned out the replacement was identical to mine. Next time I will have a lil more confidence in the instructions given.