JGD8430ADF15 Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jerry W. from Weiser, ID
- Parts Used:
- WP7737P245-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken knobs on the drop in range top.
My son that is now in the Army National Guard was rather rough on the knobs for the range. Instead of pushing down and then turning, he would just turn the knobs and broke three of them. I only had one left that would operate all of the burners. I searched all over the local area and could not find any replacements for them. I went to the internet and found your site and the exact knobs I needed to replace the broken ones with. I received the new knobs in the mail and then put them on the range. It is nice to have knobs that actually work and it makes cooking much easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Grenada, MS
- Parts Used:
- WP7733P410-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner knobs broken
Lifted upwards on old knobs to remove then aligned new knobs fittings, pressed downward to instal new knobs. Really easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KEN from REDDING, CA
- Parts Used:
- WP7737P245-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Knob
Take old off and put new on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Port Charlotte, FL
- Parts Used:
- WP7737P245-60
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
cracked knob on stovetop
the cracked knob left the round piece of metal that is part of the knob inside the stovetop, preventing the new knob from being installed at the right height. We were able to remove the metal piece and place the new knob on at the correct height. We were very pleased at how fast the part was received.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- edward from nanticoke, PA
- Parts Used:
- 74007735
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner porsclend was cracked and would not light
removed grate and cap.unscrewed burner plate.disconnected spark wire and replaced with new part.fired it up .now it workes again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KARL from OCEAN, NJ
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
burner ignator split--
unscrewed old ignator---replaced w new--done deal!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from Spring, TX
- Parts Used:
- WP7737P245-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
plastic split
remove knobs from pkg, remove broken knobs from range insert new knobs wallah done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Harrisville, RI
- Parts Used:
- WP7737P245-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
The female D stem fitting of the control knob cracked, we could not turn on / off or control temperature to that heated area.
We replaced the control knob with an exact replica from PartSelect at a very reasonable price – Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yosh from Mill Creek, WA
- Parts Used:
- WP7733P410-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner knob socket was broken
pull out the old knob and replace with a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aida J. from North Richland Hills, TX
- Parts Used:
- WP7733P410-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
knob got burned
I just took-off the old one and put the new one by hand.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Glenwood Springs, CO
- Parts Used:
- WP74009336, WP7733P410-60
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
One burner not lighting, but has spark
Electrode ceramic was chipped. Spark was not coming to the top of the electrode, and stove would not light. Remove two burner screws. These are "baked" on...so use some liquid wrench first if you have it. Don't strip the head, or you'll have a mess. Remove burner, unplug electrode, remove electrode screw, replace electrode. Reverse process and you're good to go!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Deer Park, IL
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Burner electrode was damaged during cleaning
A crack in the porcelain caused the spark to not go in the proper direction, therefore the burner would not ignite. To have the job done by a professional would have cost $200.00 plus parts. Remove two phillips screws lift the burner out then remove the one phillips screw that held the electrode. Then with the new electrode in place reverse the previous steps.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from Iuka, IL
- Parts Used:
- WPW10154101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Burner Head was leaking gas from side
I lifted the burner tray from stove turned it upside down then removed six small screws from side of cover pan then I removed the cover then I removed the screws from the back of the old burners and igniter.Then I turned the old burner counter clockwise and it lifted out easly. the igniter is removed with no problem. The new burner is put in place and turned clockwise to lock in place.Then replace then the gas tubes and igniter and igniter wire then put tray cover on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roy from Olympia, WA
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
igniter would spark, but not light flame
Installed new igniter, but would still not light flame. Determined it was a design flaw. On our range, the 2 right hand burners have "lift-off tops" that are farther away vertically from the igniter than the smaller left hand burners. I placed asmall nut from a nut-bolt assembly on top of the igniter, and now the igniter sparks higher to the "lift-off top" and the flame ignites everytime. Without that added heigt, the igniter just sparks uselessly around the base of the burner. There should be a higher igniter designed for the higher distance between the igniter and that removable top. Good luck with your own modification.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from Franklin, TN
- Parts Used:
- WP74009336
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Cook top electrode "starter" not working
Do not buy just the burner electrodes. The screws that hold the electrode will break off. Purchase the burner head with electrode. I would recommend placing anti-sieze lub on the new screw that holds the electrode to the burner head so if the electrode fails again it can be replaced. The screws that hold the burner head to the top top are mild steel and will rust and snap off. I would use a rust penatrent on these screws several days before trying to remove but most likely they will strip or break off. Replace all these burner head screws with stainless steel screws with anti-seize applied. If any of this sound difficult call a repair company.
Was this instruction helpful to you?
Thank you for voting!