JGD8430ADF15 Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Charles from Grenada, MS
- Parts Used:
- WP7733P410-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken knobs
First I removed the old damaged knobs by pulling upward on the knobs. Then I replaced the damaged knobs with the new knobs being careful to align the male and female connection. After installation I tested each burner for proper operation. As a final test, I asked my wife for her opinion. We're happy!
Charles & Dorothy
Charles & Dorothy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Mesa, AZ
- Parts Used:
- WP7733P410-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Burner nob broken
Popped the old one off and installed the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Potomac, MD
- Parts Used:
- WP74009336, WP7733P410-60
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ignitors with VERY weak sparks (2 Burners)
Should have read the partselect instructions first 1.) unplugged range 2.) unscrewed (torque screws - good thing I had some) burners - one screw was corroded into the top and snapped - will require a drill to remove and replace metal screw. 3) slid electrical wire from contact 4.) unscrewed (with phillips) Burner Electrode assembly (also corroded - took some force) replaced electrode assy and reversed steps. Works perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anita from Gloucester, MA
- Parts Used:
- WP7737P245-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Brocken Burner Knob
This was a simple replacement of a burner knob. The website had exactly what I needed, including a photograph so I was sure it was the exact match. Delivered quickly and was perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from neuvo, CA
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ignitor cracked on 3 of my gas top buners
I used a star head driver to take of burners ,then pulled wires out about 2 inches unplugged old ignitors and plugged in new ones
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Overland Park, KS
- Parts Used:
- WP74009336
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The ignitor went out on one of the burners of the gas range
Remove the burner cover to reach the burner assembly. From the top of the cooktop you will see 2 screws holing the burner assembly. Using a T drive (6 point screwdriver)remove both screws and the burner assembly will come out of the cook top. Using a phillips head screw driver, remove the old ignitor from the burner assembly. Mine was galled up, so I had to use some penetrating oil and let it sit for a half hour. I then used a hammer and a phillips head screwdriver to tap the screw as I twisted to un-tightened the screw. Once it broke loose, I placed the new ignitor and reassembled the burner into the stove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Granite Bay, CA
- Parts Used:
- WP7733P410-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
my knob broke
There is really nothing to replace a stove knob. What I was impressed with was the speed in which the knobs came to my house, the very next day from the day I ordered them.
Thanks a ton!
Thanks a ton!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Cresco, PA
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Range would not light.
First I removed the burner, two screws held it in place. The ignitor is attached to the burner with one screw remove the screw then remove the one wire connection. Reverse the steps to put back together. The whole job from start to finish takes about five minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Half Moon Bay, CA
- Parts Used:
- WP7737P245-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
A plastic handle cracked and was loose.
I lifted off the broken handle and replaced it with a new handle. It worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tamara from Crown Point, IN
- Parts Used:
- WP7733P410-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
original knobs were broken. They are only plastic afterall and no did not hold on the stem to turn on and off without duct tape.
Simple. I went online, found the replacement part, ordered 5 new knobs. They came within 4 days and I put them on. Easy as can be. I saved this site so I can go back to it if I ever need to. Wonderful! Thank you..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Sumas, WA
- Parts Used:
- WP74009336, WP7733P410-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
electrode would not spark
removed two screws, lifted the element, disconnected wire, removed one screw that holds electrode, replaced anf assembled
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Hendersonville, NC
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ignitor cracked and would not light
Simply removed the old ignitor and install the exact replacement part. Work great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Alta Loma, CA
- Parts Used:
- WP7733P410-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knobs split, was getting inaccurate flame
Remove old knob. Replace with new knob.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from La Habra, CA
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken electrode
First I tried twitching my nose....after I stopped sneezing I got a screw driver and put the new electrode in and gosh in gahiggy, it worked!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Buena Park, CA
- Parts Used:
- W11087445
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
Gas explosion due to bad Gas Pressure Regulator
First step is to turn gas off to cook top and also disconnect power to the unit. Than using a crescent wrench disconnect the gas line going to the unit from the Regulator. Than again using the crescent wrench disconnect the regulator from the bottom of the unit. Next remove the nipple that connects the gas line to the regulator from the old unit. Apply new pipe dope to the threads and screw it into the new one and tighten down. Next install the regulator to the unit and install the gas line to the regulator. once done with the install you can now plug the unit in and turn on the gas. You are now ready to use the cook top again
Was this instruction helpful to you?
Thank you for voting!