JED8230ADB15 Jenn-Air Cooktop - Instructions

I first thought it was the switch. I ordered one and the wrong one was shipped to me FROM ANOTHER COMPANY. After more trouble shooting I discovered it was the cartridge that needed to be replaces. I ordered one and again, the wrong one was shipped to me. They told me I could not get the right part because they were not made anymore.

So, I shipped it back and got in touch with Part Select. They found the right part and shipped it to me in 2 days. Problem fixed with the EXACT right part. I ordered the first part more than two months prior to receiving the correct part from PartSelect. All I had to do was plug it in to the recepticle in the stove. No tools required.

Lifted the grill out and slid the new burner unit in place. This was very easy; no problem at all.

Flip the breaker. Lift off the fan center grate. Remove two screws located on back of the burner dials housing. Lift the back of the housing, then pull this gently away from the front to unhook the front. Turn this over, locate the switch. Pull the three electrical plug connections from the switch plastic housing, remembering their locations. Back off the two nuts holding the switch to the underneath side of the dials housing. Place the new one in place, put it all back together.

Removed the cooktop using screwdriver. Pushed lens-light into cooktop hole.It was difficult to do and was where I spent most of my time. Next time I will spray bottom of lens- light with silicon so it goes in easier. I stood cooktop up on its side and inserted the red light assembly onto the lens-light. Reinstalled cooktop
and turned electrical power on.

I got the switch wired correctly, with much cussing. It worked - burner heated. But I couldn't get the new switch to fit back with the old ones neatly enough to close the box and secure it. Got help from someone with stronger hands but still couldn't get it to fit. On top of that I found that the new knobs didn't fit on the new switch - or even on the old switches. The old knob didn't fit on the new switch either. I gave up. Removed the new switch and took out the corresponding burner. Still have 3 burners that work.
Repair folks had warned me that I couldn't get parts. They didn't say that it would look like there was a replacement part but it wouldn't fit!

We removed all the screws in order to remove the top cooktop frame. Once we did, the bottom part of the cooktop fell! It was being held up by the vent that goes underneath. My son and I had to get underneath to push up while my husband tried to position the cooktop back over the counter top ledge. It was VERY heavy. This was difficult and needless to say, it fell a couple more times before we finally were able to keep it on the ledge. We had to turn off the electricity, pulled the element out and disconnected the two wires, installed the new light and then placed the cooktop cover back in place by screwing all the screws. We did test the light before screwing on the cooktop cover JUST in case...:) It worked!

I first turned off the power to the range. The switch was housed inside a control panel in the front center part of the range. Two screws were removed and the housing was lifted forward and then off The switch was held in place by metal friction washers. Those were removed by a screwdriver and then the switch slide off the posts that they were attached to. The switch had two wires and I simply replaced the wires onto the new switch and placed the switch back onto the posts. The friction washers were pressed back over the posts to hold the switch in place and then the housing was screwed back into place.

Turned off power to range top. Two screws to lift the control area. One snap on was burned off.
Removed tab from inside same. Used nut driver to remove switch. Taped wires and restored control area. Power back on. Went to computer and got website for Partselect. Found description of part got me to several choices. The range is 25 years old. Selected a switch that seemed close. It arrived in two days. Redid the same steps. Some file and drill work required to make switch fit. Screwed switch in place. Untaped snap connectors and attached to switch. Checked for function and and restored control area.

I took them out of the box, Took the old Elements out and put the new ones in, It was a piece of Cake, You have wonderful girl working for you, she was just great. thanks for the good service. my range looks like a new now. Nora

1. Remove the exhaust vent cover, located in the center of the top of the range. It just lifts off.
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover

Just plugged it in

just wanted another set of burners before Thanksgiving or Christmas rolled around and all I have ever had was two plus the grill part of my Jenn-Air. But I did find your site very easy to use and the delivery was very prompt and the packaging was wonderful. I have bookedmarked your site so that if I need anything again for my kitchen I will look at you first.

Take cartridge out of box, slide into slot, done.

It was so easy. I just unplugged the old catridge and plugged the new one. Thanks for the fast and great service at a competetive price. I am a very satisfied customer who will definitely be returning and recommending your service.

throw breaker, unbolt switch, unplug leads, rerplace switch, bolt in place, reattach leads, turn breaker back on