W238 Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- stephen from canton, MA
- Parts Used:
- WP74008014
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the hinge sring broke on one side of the oven door
Remove the screws from bottom of door to gain access to the hinge screws. Remove the bottom hinge screws and then open the door to gain access to the top hinge screws. CAUTION after removing the top screws close the door as far as possible while still griping the sides of the door. Pull up on the sides to remove the door from the stove. The springs are fully loaded if you have the door open all the way and try to lift up (like I did) the hinge will spring back and get your finger. Install the new hinge, put the door back into the oven, install all the screws and then remove the temporary rivet that comes installed in the new hinge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from Brighton, MI
- Parts Used:
- A341
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cooktop/grill scratched up
I bought 2 covers, they are great, I can put them on and the cook top looks wonderful. I bought an older home and the Jennn-Air top was scratched up, now you cant tell at all when I put the covers on. I was thrilled to find them. I thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lark from Mill Creek, WA
- Parts Used:
- W11120795
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
two burners had failed to work properly. Always went to full heat.
I first removed power from the stove at the breaker panel. Next, I used the assembly diagrams provided by the parts select website to determine how to open up the stove panel. I opened the oven door to access the four screws holding the front panel holding the knobs. I removed the screws and was able to tilt up the front panel to allow access to the four burner switches. It was easy to swap out the wires on the old defective switch to the new replacement switches. I replaced both defective switches in 15 minutes and tiled the front panel back down into its normal position and put the four screws back into the panel to secure it. Then I turned on the breaker and did a check to see that the parts I replaced were working properly. They were and the total repair time was around 30 minutes without rushing at all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from Garland, TX
- Parts Used:
- W11120795
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Element wouldn't regulate; always on high
We turned off the breaker and removed the screws holding the control panel in place. They are behind in the exhaust area.
The control unit was lifted up to reveal all of the wires and the switches. Using pliers I pulled off the connectors keeping up with which wire was from which connector. The switch then dropped out and the new one went in and wires were reconnected.
It was not difficult. Only challenges were that it was very dense and hard to get at the wires and you had to be careful to keep up with the wire locations.
Well worth the time...I can do something other than boil water on that burner!!
The control unit was lifted up to reveal all of the wires and the switches. Using pliers I pulled off the connectors keeping up with which wire was from which connector. The switch then dropped out and the new one went in and wires were reconnected.
It was not difficult. Only challenges were that it was very dense and hard to get at the wires and you had to be careful to keep up with the wire locations.
Well worth the time...I can do something other than boil water on that burner!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Tacoma, WA
- Parts Used:
- A122BA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replacement of Grilling element with radiant cartridge
First had to find an element that was available for this older model stove top. I wanted to change the grill section for additional burner elements. We ordered two sections. The "guts" just unplugs and the new elements slip right in. It is like having a brand new stovetop! My wife is very happy with the four burners and doesn't miss the griller that were only used sparingly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dale from Alpharetta, GA
- Parts Used:
- W11120795
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
burner on electrics range was either off, or fully on
The burned control switch was not functioning. It took a while to find the range model number and then the part number of the switch. It was cool that I could see a picture of the part with the part number on the internet so that I was sure to buy the right part.
Once the part arrived, I turned off the power to the range (circuit breaker, 220 V) removed two screws, used nut driver to disconnect switch handle, marked the 5 wires going to the switch, used the needle nose plier to remove the wires, the attached wired to the new switch, placed switch back into position, used nut driver to attach switch to the control unit. Rescrewed control unit in place with two screws.
turned on circuit breaker and tested. All good.
It is clear that this old Jenn Air range and be completely redone to good as new. All parts are available
Once the part arrived, I turned off the power to the range (circuit breaker, 220 V) removed two screws, used nut driver to disconnect switch handle, marked the 5 wires going to the switch, used the needle nose plier to remove the wires, the attached wired to the new switch, placed switch back into position, used nut driver to attach switch to the control unit. Rescrewed control unit in place with two screws.
turned on circuit breaker and tested. All good.
It is clear that this old Jenn Air range and be completely redone to good as new. All parts are available
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joanna from cary, NC
- Parts Used:
- JEA7000ADBA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
elements didn't work
This was so easy, it's a replacement that just slides into the outlet at the back of the stove. Done, just like that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ardis from San Angelo, TX
- Parts Used:
- JEA7000ADBA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
top burner modules were burned out
slipped the old modules out and installed the new modules by slipping them into the cavity and into the electrical connection.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephan from Port Kent, NY
- Parts Used:
- JEA7000ADBA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed Coil element to supplement grill element
Unplugged grill element and plugged coil element.
Install was as easy as was ordering from PartSelect.com.
Price and availability plus timely delivery will make me a return customer.
Install was as easy as was ordering from PartSelect.com.
Price and availability plus timely delivery will make me a return customer.
Was this instruction helpful to you?
Thank you for voting!
replace blower motor
disassemble housing and remove fan and motor. Reatach fan to new motor, connect wiring, place gasket around motor and reassemble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Sarasota, FL
- Parts Used:
- A122BA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I wanted to convert the grill to burners
I removed the grill top and unpluged the element. then i pluged in the radiant element cartridge and i was done. It took me longer to unbox the cartridge than to install it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GEORGE from WARRENTON, VA
- Parts Used:
- JEA7000ADBA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The 25 year old 2 burner element was worn out.
1-Unplugged the old 2 burner element.
2-Plugged in the new element.
3-Elapsed time approx. 10 seconds.
4-It took longer to remove the new element from it's shipping
carton than it took to remove the old & install the new.
2-Plugged in the new element.
3-Elapsed time approx. 10 seconds.
4-It took longer to remove the new element from it's shipping
carton than it took to remove the old & install the new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gwendolyn from Halifax, PA
- Parts Used:
- A122BA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My Jenn-Air stove top cartridge paint was peeling.
I removed the stove top cartridge from the stove top and plugged in the new one. No tools were needed. It was very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Andersonville, GA
- Parts Used:
- JEA8120ADBA
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replaced griddle with burner cartridges
First of all the part arrived a day and a half after ordering which we thought was remarkable. We unplugged the griddle unit and plugged in the cartridge with two burners. It is beautiful.
Thanks.
Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Duane from Niceville, FL
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
smell of a dead animal
The 15-year-old Jen-Air stove started smelling really bad. I thought it was a dead animal stuck in the exhaust tube which runs under the floor to the outside. I flushed it out with clorine bleach, but it was still bad. It turned out to the be the grease filter. I washed it every week in the diswasher, but it just was not enough to get it clean enough. Finally, the grease went rancid and smelled really bad. This "repair" took about 30 seconds.
Was this instruction helpful to you?
Thank you for voting!