C201 Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- ELOISE from MILFORD, OH
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced filter
pulled old one out , cleaned the area & replaced with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- deborah from fort pierce, FL
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old grease filter that I actually did not know I had to change
Removed the old grease screen and cleaned the entire area thoroughly and replaced the screen
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Carthage, NC
- Parts Used:
- 12001676
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Stove top element not working due to bad receptacle.
Turned off the power at the breaker box, cut the wires approximately 5 inches from the bad receptacle and removed it after removing one screw. Stripped back the wires about 1/2 inch and attached the new wires with the ceramic wire nuts provided and secured the receptacle back in place with the new screw provided in the kit.
My sister's husband wanted to scrap the whole range but I repaired it with $14.00 worth of parts.
The element is working great now.
Whenever I need appliance parts again I'll use partselect.com.
My sister's husband wanted to scrap the whole range but I repaired it with $14.00 worth of parts.
The element is working great now.
Whenever I need appliance parts again I'll use partselect.com.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marion from aspen, CO
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My Jenn-Air is an "antique." The filter was disgusting!
I had put up with a filter that got more and more raggedy every year, but I thought my 30 yr. old range/grill top was too old for me to find an replacement filter. What a great service you offer. I found you by web-surfing, typed in the model #, and presto--you sent me the shiny new filter. All I had to do was pop it in and throw away the nasty grill (after washing the scent off to keep the bears out of my Colorado garbage.) Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roe from Raleigh, NC
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Falling apart 20 year old grease filter for downdraft counter rangetop
Cleaned out the downdraft cove, inserted the new filter, and put old filter in garbage can. Laughing. Thanks. Wish you had a FAQ's hotline. I'd like to know if the radiant inserts fit the older coil-type models.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Charlotte, NC
- Parts Used:
- WPY04100166, WPY04100165, WP707929, 12200035
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cooktop was looking old and worn though there was no working problem.
All of the "old" pieces were very easily removed and replaced with the new pieces. The update looks terrific and works just fine!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eric from North Andover, MA
- Parts Used:
- 700855K
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Burner had no temperature control other that full on.
Locate and open appropriate breaker to kill power to the range. (very important if you intend to see tomorrow).
Pull off the control knob.
Remove 2 screws that hold in control pannel.
Lift out the control pannel to the extent that the wires will let you. (2-3 inches)
Remove the nut that holds the switch/controller in the pannel.
Remove the wires one at a time and reconnect them to the new switch. Make sure to connect them the same way on the new switch.
Re-install the switch in the pannel.
Re-install the pannel in the stove.
Close breaker and test burner contol.
Pull off the control knob.
Remove 2 screws that hold in control pannel.
Lift out the control pannel to the extent that the wires will let you. (2-3 inches)
Remove the nut that holds the switch/controller in the pannel.
Remove the wires one at a time and reconnect them to the new switch. Make sure to connect them the same way on the new switch.
Re-install the switch in the pannel.
Re-install the pannel in the stove.
Close breaker and test burner contol.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- george from burke, AL
- Parts Used:
- WPY707454, WPY707453, WPY04100166, WPY04100165, 715878, 715877
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Wanted to update surface parts to a very old (27 yrs?) Jenn-air range on an island
The first task was to find the rings, drip bowls and elements on the "PartSelect" webpage. It was surprising easy, especially since I have no experience whatsoever in replacing range parts. The ordering was straight-forward, and most of the parts arrived within a week, a couple were back-ordered, but arrived a week later. Instillation was easy - just unplug elements, lift parts out, and insert new parts. I made a mistake in ordering - for the left side of the range, no adaptor rings are needed. I returned these excess parts to PartSelect, and within a week, they refunded the costs of these parts. Overall, I'm very please with the parts and service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lucille from Mattoon, IL
- Parts Used:
- WPY700854, WPY04100166, WPY04100165, 715878, 715877, 12001676
- Difficulty Level:
- Difficult
- Total Repair Time:
- 15 - 30 mins
Wanted to "renew" cook top
The drip pans, burner knobs and electric surface elements are easily removed and replaced. The new receptacles for the burners were NOT easy to replace, but electricians were on hand to install when they replaced the cook top into the new counter top. Even the electricians had to read the instructions - and remove the control panel to replace one of the receptables. Looks like a new cook top.
Was this instruction helpful to you?
Thank you for voting!
blower motor died
Pulled the motor and blower wheel from below. Replaced both. I think it was easier to replace the two together than just the motor.I also had old light indicators so we replaced them since the stove was sort of apart. The repair was not difficult at all, and my 30+ stove top looks and runs great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Poway, CA
- Parts Used:
- WPY700854
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lettering on old stove knobs was no longer visible and knobs were loose.
Took the old knobs off and replaced them with the new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Chino, AL
- Parts Used:
- WP5701M122-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Just ugly this time`
It's wonderful to get accessories for this 20 year old Jenn-Air. I love it and now it looks like new.
Was this instruction helpful to you?
Thank you for voting!
Fan switch burned out, Burner switch only worked on HIGH.
Well, since the circuit breaker blew when the fan switch burned out, I was hoping to get a new counter-top range out of this. But, no such luck. My son opened up the control module (2 screws under the fan grill) and found the problem. Then I decided that if I needed to replace ONE part, I'd replace ALL of the parts that didn't work and were worn out.
First I turned off the breaker all the way, then, since the module was open anyway (it pulls out about 2 inches), I only had to remove the old fan switch using the socket set, and replace it, wire-for-wire with the new one. The flange needed to be filed down a bit because it was wider than the original, but not a problem to do. I had to use the original nuts to hold in the new one. The new ones are smaller. Just used the socket set in reverse
....done!
The burner switch and knobs were a little more of a problem but only because ordering them didn't follow the rules...I needed series 3 parts, even though I had a "Run 01" range top. With the help of a very nice customer service rep, I got the correct parts the next day and replaced the burner swich the same way...used a socket set to loosen and remove the old switch and connected the new one wire-for-wire, and again needed to use the original washer and nut. (The wrong model that I initially received had a new washer and nut in the bag with the switch.) But, again, no problem.
The control knobs just pull off and push on...simple.
Now that I had a nearly new range top, I spent another 2 hours REALLY cleaning it (Dawn Power Dissolver is GREAT!). Looks almost like new! I guess I won't be getting a new range top for another 22 years now.....
First I turned off the breaker all the way, then, since the module was open anyway (it pulls out about 2 inches), I only had to remove the old fan switch using the socket set, and replace it, wire-for-wire with the new one. The flange needed to be filed down a bit because it was wider than the original, but not a problem to do. I had to use the original nuts to hold in the new one. The new ones are smaller. Just used the socket set in reverse
....done!
The burner switch and knobs were a little more of a problem but only because ordering them didn't follow the rules...I needed series 3 parts, even though I had a "Run 01" range top. With the help of a very nice customer service rep, I got the correct parts the next day and replaced the burner swich the same way...used a socket set to loosen and remove the old switch and connected the new one wire-for-wire, and again needed to use the original washer and nut. (The wrong model that I initially received had a new washer and nut in the bag with the switch.) But, again, no problem.
The control knobs just pull off and push on...simple.
Now that I had a nearly new range top, I spent another 2 hours REALLY cleaning it (Dawn Power Dissolver is GREAT!). Looks almost like new! I guess I won't be getting a new range top for another 22 years now.....
Was this instruction helpful to you?
Thank you for voting!
The drip bowls were old and stained; the knobs were so worn that they could hardly be read.
OK, this was easy, and it's a good thing 'cause I'm so blonde when it comes to repairs. But I will have to say this, my Jenn-Air looks like new and it is 29 years old. Thanks Partselect for making my repairs so quick and easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Orange, CA
- Parts Used:
- 12001676
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Burner was out but the burner coil worked on onother burner
Replaced receptacle but it was not the problem. After further inspection I believe that the problem is the switch. The switch is on order now from Part Select.
Was this instruction helpful to you?
Thank you for voting!