JGD8348CDP Jenn-Air Cooktop - Instructions

Remove 7 screws to remove cover. Disconnect ignitor wire. Unscrew gas supply. Twist burner head to remove (can be difficult). Reverse procedure.

Original bumper pads NOT glued into the burner grates. Hence they began to disappear during routine use and cleaning. Very simple repair with a little glue this time around. But fairly expensive for a very small part set

Been looking for grate pads for 10 years and finally found you site and part # WPL 814323.
Wasn't sure that they would fit but couldn't even find new grates so decide to try them --Fit perfect.
Kitchen aide stove top gas with round grates. Used the drill to clean out the holes with broken pads still embedded.With clean holes the new pads just screwed in like the originals. Thank you very much

Even though the ceramic insulator looked new (white), it had become non-functional, replacement was simple, 2 phillips screws, reassemble and test. Now I will have to order the other 3.

cleaned out pad area with an awl. then the pads just slide in.

I first had to purchase the replacement motor which was quoted from a high of $236 to a low at graingers of$100. 00. The counterman at graingers removed the blower fan from the motor for me with a special long handled allen key. I then degreased and cleaned the blower fan. I had to cut off the screws on the motor and replace the 3 motor isolators and the urethane foam around the motor. I had to thread the 3 wires from the new motor through the bx cable from the old motor and reattach the fan to the motor. Anyone wanting more detailed informatioin may contact me at:mablume@optonline. Net

The Model number could no longer be read clearly on the stove electric grill with a down draft vent system, so all I had was the size and looks of the old grease/air filter. I was very happy to come across Parts Select by way of an amazon.com search. Their web site's design and the parts pictures with detailed descriptions made it easy to find exactly what I needed. The grease filter fit perfectly in no time. I have successfully used my cooking grill again.

The lids are fastened to the underside of the unit by rivets....3 to each lid.
I used a cordless drill and small drill bit to drill through the rivets to remove the old lids and remains of the rivets.
The new lids are easily fastened back using a rivet gun ( about $20 in Lowes) using small 1/8th aluminum rivets.
No real problems.
1 thing to note is that the drill bit will pass through the old rivet by about 1/4 inch before it comes up against the upper level of the BBQ floor so do not drill any deeper.The aluminum rivets are easy to drill through and you will easily feel when the rivet is drilled through.

I used the other good burner assembly to isolate the problem to the igniters or the igniter block. I ordered both parts from Parts Select. They shipped the parts promptly and after 10 minutes of install time, the burners worked flawlessly.
Thank You Parts Select.

blower wheel was caked with dried grease clumps; replaced blower wheel, urethan foam and 3 motor isolators; blower/fan no longer vibrating cooktop.

The flame holder twists about 1/2 inch to left and lifts off. I removed the two screws that holds the igniter on and removed it and installed the new igniter.
There was one complication: when I put it back together, there was no spark. I removed the ground wire and cleaned and scraped it and replaced it and still no spark. But, for no apparent reason the spark returned and has been okay since.

Shut off gas supply
Pulled stove away from wall removed spark ignigtor box .
Installed new one .
No problem.
Good for another 10 years

Simply remove the box containing the two right burners. Access the igniter by removing about 8 screws and pull the coupler for the igniter off with a pair of needel nose pliers. Replace with new igniter using the same tool. Re-assemble the box by screwing in the screws and give it a try. Worked great. Once slight hitch, be sure you don't leave a second screw driving in the box. As it will raddle. So I had to remove and reassemble twice. I'm not a surgeon! Thanks for the fast delivery!

I haven't done anything yet because the part I am replacing is different from the one i have to order. I guess you might say I am getting screwed. I purchased the grill burner for $234.00 plus tax and shipping. Then realized I needed to purchase an igniter. My original one came with 2 igniters attached to the burner part. These new ones are all separate. $55 and $49 if i remember correctly. I ordered just the larger one and I am hoping I do not have to buy the smaller one. The large igniter will not even arrive until the end of August that is 6 weeks after the order date. I was told by the customer service rep it would only take 10 days to get it to the warehouse.The price tag is over $500 just to replace the grill burner on my stove top.That is some rip off. Otherwise my stove top is in excellent condition.

remove grate - flip upside down - be sure holes are clean and dry - using toothpick, swab some RTV sealant into the holes and a bit on the pads ... insert pads till they seat - be sure to hold in place till all air is evacuated - wipe excess RTV with paper towel...DONE