CCG406L Jenn-Air Cooktop - Instructions

First, unplugged the cooktop from outlet and shut off gas. Then, removed burner assembly then located and removed existing spark module. Installed new spark module kit, reassembled burner assembly and then plugged unit into electricity and turned gas on. Was rewarded when testing burners with an instant ignition.

Opened oven door. Inserted a small bent nail into the small holes on the hinge. This locks the hinge from closing all the way. Removed the chrome hinge retaining plates. One at each hinge. Lifted the door off the oven. Laid door on towel. Removed 3 screws from the top of door, three screws from the bottom of door. This allows you to separate the two pieces of the door. Clean all glass surfaces, including the ones under the middle glass panel. Removed 1 screw from each hinge at bottom of door. Pull hinge from bottom of door after removing screws. Insert new spring at top of door first, replace retaining screw. Realign the two door parts and replace all screws. Set door back on hinge pocket. Be careful to insure that the hinge seats into the pocket. Open door just enough to replace retaining plates. Process was easy, but it did not fix the problem completely. Bought heavy magnets from hardware store and installed them inside the door. This with the new hinge fixed the problem.

Unlike many here, the oven door closed enough to come up to temperature quickly and I could not feel any heat escaping. The oven worked fine but the light stayed on because the door just wasn't snug enough. I watched the great how-to video and ordered the hinges. They arrived in two or three days! I set up a work space, cued up the video again and the new hinges were installed in just a few minutes! But the door would not close enough to turn the light off! I did some more googling around and found the magnet trick! I just happened to have the perfect size magnet from a broken souvenir magnet! and now the light stays off! I stuck the magnet (about the size of a nickel) inside the door opposite the light button. This won't help if you have serious problems with the oven door, but it works if the only problem is the light!

sorry, son did job. It went like a charm. Easy, quick, and works great.Thanks

We found the youtube video created by partselect.com and followed it. We took the door apart, cleaned the inside, removed the old hinges and replaced them with the new ones. Now the door works perfectly!

I followed the online video at Jennair.com. The repair was easy and I saved quite a bit of money. I was quoted a price of $534.00 to replace the door hinges, I did it for $96.00 including overnight shipping chargers. I am a very happy lady.

I removed the pan and then the burner assembly. Used a nutdriver to remove the old front burner. Replaced with the new part, tightened it on, and tested the new burner. Worked first time. Extremely easy. It took less than 5 minutes to replace.

Slide the knob onto the shaft.

The issue: the burners were abused by the previous tenant, the burnt grease was clearly visible. They would hardly ignite and the smell of gas was always present.The remedy: new burners. They were hard to find, I was not completely sure about to stove model (it could be quite a search to find the right ones). There is a front burner and a back one. I was not sure from the diagram about the back one, so I called Partselect and someone answered the call right-away. The burners arrived a few days later, and they were the correct ones. The burners are not Jenn-air specific, it looks like several brand names use the same ones. The installation was extremely easy, a few hex screws. The stove is like new. I highly recommend Partselect.

Took two screws out of each burner and put new burners in and replaced the screws. A real piece of cake. and they work great. Did not even have to adjust the flames. They were all solid blue and perfect. Bill

Pop off the old and on with the new. Took longer to open the plastic packaging each came in than to remove & replace old knob with new.

I did not have the model number and thought I picked the correct knob by the picture. I sent back the knobs and one of my knobs to see if the company can match.

pried off the old knob with hubby's needle nosed Leatherman pliers and popped the new one on!

Hardest part of repair was ordering part. The knob arrived the day after my placing order. Not rocket science to replace burner knob.

Inserted new knob on to the stem... very difficult operation taking a great amount of skill. ;-)