CCG406L Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Linda from BOLIVAR, TN
- Parts Used:
- WP7505P283-60
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Front burner wouldn't light because hole burned in metal tube that channelled gas to burner
So very easy!!!! I'm a 70 year old grandmother with a small socket set - and that's all I needed! Removed one small screw, removed old burner, popped new burner in, replaced one screw, and back in business! Placed order, received it in 2 days, fixed burner. So much faster than calling a repairman!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JoAnn from Raleigh, NC
- Parts Used:
- WP7505P283-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
This item needed replacement for the 3rd time due to finish wearing off, within 6 months EACH time.
unscrewed previous unit, placed new unit and screwed in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Silver Spring, MD
- Parts Used:
- WP705105
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
to convert a cook-top stove with 2 burners and a side grill into a 4 burner stove.
Replacing the side grill burners was easy--lift off the grill covers and pull out the grill burners. Next, attach the new front and rear burners to the burner plate with 2 screws (the older version uses 4 screws) using a nutdriver. Place the 2 burner unit (now joined) into the 2 gas inlets (no screws necessary--just slip them over the tubes). Insert the grill pan over the burners and place the 2 burner grates over each burner. Done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from ALTADENA, CA
- Parts Used:
- WP74008014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Hinge on one side had snapped.
Although only one side hinge had snapped, I replaced both sides with new oven door hinges. Followed the website video installation directions and all went well; the new hinges work perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from SCROGGINS, TX
- Parts Used:
- WP74008014
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Both door hinges was simply worn out from 20+ years of usage.
Bought a pair for needed door hinges for replacement. Found a DIY video on You Tube showing technique to replace. Door removal was a bit awkward but hinge replacement and door reinstallation was as detailed in video. Could not nor would not have tackled this project without video. Premium quality parts sent and received within days of ordering. Wife happy therefore so am I.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John H from Newfoundland, PA
- Parts Used:
- 74005189, WP7505P283-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Burner Ports were worn and oversize
Removed the two screws that hold burners on mounting bracket . Removed burners and installed new burners. re-adjusted air flow to elimenate yellow flame.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from Palm Coast, FL
- Parts Used:
- WP7505P283-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
didn't ignite gas range.
After getting help from customer support, I was able to order the part. I tracked the part on FED EXp.
After deliver the part was installed and working in 5 minutes. All that for less than $50.00.
After deliver the part was installed and working in 5 minutes. All that for less than $50.00.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Portland, OR
- Parts Used:
- WP7505P283-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Front burner inoperative
Simply removed the front burner using 1/4 incn nutdriver on
two screws.placed new burner in position and tightenwd two screws.
Simplest and easiest job I ever did!
Works as new!
two screws.placed new burner in position and tightenwd two screws.
Simplest and easiest job I ever did!
Works as new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Monmouth, OR
- Parts Used:
- WP74008014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken oven door hinge
I watched a You Tube video,removed and dismantled the door, installed the new hinge. I forgot to remove the small pin which is similar to a rivet. When I tried to close the door it bent. Eventually, I remembered the shipping pin and pulled it out with any damage. Believe it or not, I had read about the shipping pin on customer comments on PartsSelect...Good luck, it is relatively easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Pittsboro, NC
- Parts Used:
- WP71001641
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
The new Maytag knobs did not depress the half-round metal post and therefore did not allow the knobs to turn.
Inside the knob, I placed a dab of CA glue on the small plastic projection , which was designed to press against the metal post, but was just shy of it. By thus building it up the knobs function perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mr. Mike F from SAN ANTONIO, TX
- Parts Used:
- WP74008014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Door hinge
My wife help take the door off. It was a little heavy . The door came apart very easy and went back the same way.We save over $300 by doing it our selfs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Martinsburg, MO
- Parts Used:
- WP71001641
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Baking element out in wall oven
My son did the repair for me. It was easy, he said. just slid it out and put new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from HOT SPRINGS, AR
- Parts Used:
- WP74008014
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken oven door hinge
My daughter & I followed the instructions in your video and had fun repairing the door. The video showed exactly how to do the repair. I hope I don't need any appliance parts very soon but I will certainly pull up your web site if I do. Thanks for an excellent instruction video.
John - Hot Springs Village, AR
John - Hot Springs Village, AR
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Poulsbo, WA
- Parts Used:
- WP7505P283-60, 74005189
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
One 25 yr-old burner was beginning to leak gas because of corrossion. Decided to replace all 4 burners.
Remove grates and pan. unscrew each burner from the metal cross mount bar, keeping in mind, the position of the cross mount bar.(Mine was not reversible.) Reverse the procedure with the new burners.
Adjust the air opening to eliminate any yellow flame. The air opening is located immediately adjacent to where the burner pipe goes into the cooktop. (Near the front of the cooktop in my case.)
Biggest problem was making sure the correct parts were ordered.
Adjust the air opening to eliminate any yellow flame. The air opening is located immediately adjacent to where the burner pipe goes into the cooktop. (Near the front of the cooktop in my case.)
Biggest problem was making sure the correct parts were ordered.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Whitefield, ME
- Parts Used:
- WP7505P283-60
- Difficulty Level:
- Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
tube was rusted out
just removed two screws - took old unit out - put new unit in.
Was this instruction helpful to you?
Thank you for voting!