JGD8430ADB Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Randy from Franklin, TN
- Parts Used:
- WP74009336
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Cook top electrode "starter" not working
Do not buy just the burner electrodes. The screws that hold the electrode will break off. Purchase the burner head with electrode. I would recommend placing anti-sieze lub on the new screw that holds the electrode to the burner head so if the electrode fails again it can be replaced. The screws that hold the burner head to the top top are mild steel and will rust and snap off. I would use a rust penatrent on these screws several days before trying to remove but most likely they will strip or break off. Replace all these burner head screws with stainless steel screws with anti-seize applied. If any of this sound difficult call a repair company.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KEN from REDDING, CA
- Parts Used:
- WP7737P245-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Knob
Take old off and put new on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Curtis from Gilbert, AZ
- Parts Used:
- WP7737P245-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken plastic chrome knobs
bought new ones and pushed them onto D shaped posts total time 90 seconds they may break again in 10 years but I am to lazy to reinforce them
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Katherine from dayton, WA
- Parts Used:
- WP7733P410-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original Burner Knob broke at the shaft
Simply took off the original knob and replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Glenwood Springs, CO
- Parts Used:
- WP74009336, WP7733P410-60
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
One burner not lighting, but has spark
Electrode ceramic was chipped. Spark was not coming to the top of the electrode, and stove would not light. Remove two burner screws. These are "baked" on...so use some liquid wrench first if you have it. Don't strip the head, or you'll have a mess. Remove burner, unplug electrode, remove electrode screw, replace electrode. Reverse process and you're good to go!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Sanbornton, NH
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner igniter didn't light burner
I removed the burner by unscrewing 2 torx head screws, disconnected wire from electrode, removed screw holding electrode, inserted new electrode,connected wire, installed burner and fired it up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Monee, IL
- Parts Used:
- 74007736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner did not light
Ordered online Tuesday, delivery by FedEx on Wednesday. Removed the old "popped" in the new and it worked right away. It was that simple. Thanks so much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sara from Mahtomedi, MN
- Parts Used:
- WP7733P410-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Knobs were damaged/distorted due to wear
Pulled off the old knobs, pushed the new ones on. Could not have been easier!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Carson City, NV
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Damaged Ignitor
Simply unscrewed the old one and installed the new one and we have ignition!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Whitesboro, TX
- Parts Used:
- WP7737P245-60
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Burner Knobs would crack in the middle
The original knobs were poorly made and kept braking. After the third set, which were very expensive for some plastic knobs, I read this web page for help. Based on what I learned and what I read, I glued the metal sleeve in the knob shaft with some super glue. I then wrapped the shaft with copper wire and spread some industrial glue over the copper wrapping, which looked like a spring around the shaft. I have had no problems in the last month. I hope it keeps up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Boardman, OH
- Parts Used:
- 74007736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Electrode cracked, spark misdirected, poor lighting
After determining it would not be possible to replace the electrode only (rusted/corroded connection), ordered burner head with electrode. Part came in approx. 24 hours. Actual repair involved removing two screws (star-shaped head),disconnecting electrical clip, removing part, connecting electrical clip to new head, reinstalling two screws. Works great now!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Geri from Brand Haven, MI
- Parts Used:
- 814323
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One of the pads on the bottom of the grate kept falling off.
I was able to order the part I needed. The faulty pad had a broken stem.Several pads came in a bag so if I have the problem again I will have the parts on hand. I bought some RTV glue suitable for items at high temperatures; used a probe to make sure the hole in the grate was clear and clean and glued the new pad in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann P from San Antonio, TX
- Parts Used:
- WP7733P410-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The plastic burner knobs were split and would not let you turn burners off and on
I ordered an entire new set even though I only needed 2...removed all of the old ones, threw away the broken ones and installed the entire set.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Dayton, OH
- Parts Used:
- 814323
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner grate pads worn off or missing
I took a jewelers screwdriver and completely cleaned out what was left of the old pads. Then applied a small amount of heat resistant rtv sealant to each hole, slid in the new pads and wiped off the excess. I let everything set overnight. The next day everything was solid. Job was complete. Note I've done this before and did not get the results I did this time. I believe it was the instruction that came with the pads and the tip-off to use the rtv. Thank you PartSelect T.Garr
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Lakeside, Arizona, AZ
- Parts Used:
- WP74009336, WP8273062
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Igniter did not work
Bought The burner with the electrode already installed. The only way to go, since the screws will not come out without breaking. Also purchased two torx screws as thay also broke. A bad design by the manafactor.Had to drill and tap out for new torx screws to fit into the gas houseing. PartSelect had all the parts I needed. Dan
Was this instruction helpful to you?
Thank you for voting!