JGD8430ADB Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Joanne from BRANCHBURG, NJ
- Parts Used:
- WP7733P410-60
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
The knob does not go down; it sticks up too high. Question? Maybe knob is not for position 2. Does it matter which place you put it on?
I tried to put knob on number 2 location. Looks like I need number 1 knob.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pat from MCKINNEY, TX
- Parts Used:
- WP7733P410-60
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
Knobs for the cooktop burners did not fit so I have returned them and still do not have use of all burners due to lack of knobs
Could not put a square peg into a round hole....parts did not fit and I do not know how to find the model number but the knob has two flat sides.l....the knobs you sent did not.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aubrey from EADS, TN
- Parts Used:
- 74007736
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Auto igniter had gone bad.
Take out 2 T15 torx screws. Lift burner assembly, disconnect igniter. Make sure wire does not return into hole. I put A paperclip on it. Connect new burner assembly. Clean under old burner. Install burner assembly with screws. Test burner.
Voila!
Voila!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from GUTHRIE, OK
- Parts Used:
- WP7737P245-60
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Knobs worn out, would not turn the post of the "D" switch.
Removed old knobs. Removed the metal insert from around the post from the old knobs with needle nose pliers. Installed new knobs. Easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from FAIRMOUNT, IL
- Parts Used:
- WP7737P245-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One was broken when bought house
Took old knobs off & put new ones on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Juan J, from UNIVERSAL CTY, TX
- Parts Used:
- 74007735
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Needed use of penetrate lubrication
Removed two screw securing wburner and disengage igniter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CHARLES from SPRING HILL, FL
- Parts Used:
- WPW10293874, WP7737P245-60
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Knobs slipping
Remove old knobs and remove old grommets. Insert new grommets, install new knobs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Potomac, MD
- Parts Used:
- WP74009336, WP7733P410-60
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ignitors with VERY weak sparks (2 Burners)
Should have read the partselect instructions first 1.) unplugged range 2.) unscrewed (torque screws - good thing I had some) burners - one screw was corroded into the top and snapped - will require a drill to remove and replace metal screw. 3) slid electrical wire from contact 4.) unscrewed (with phillips) Burner Electrode assembly (also corroded - took some force) replaced electrode assy and reversed steps. Works perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herbert from LATON, CA
- Parts Used:
- 814323
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Rubber grate pads that protect the range top had worn and were flat.
It didn't. The grate pads (PN# PS389174) were too small for the grate (W10311216) and wouldn't work. (PN# recommended by Whirlpool parts department) The pads were smaller in diameter and shorter. Yes I could have glued them in, but because of the size the pads would be flat in no time. The only thing I could order from KitchenAid was the total grate. I ordered the pads late December, they were backordered. I got them the 1st week of February. I tried getting through to Whirlpool by calling to see if there was something I could reorder, but no luck, couldn't through. Am I unhappy? Oh some, but I handle it. Its not the first time I have been rode hard and put away wet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anita from Gloucester, MA
- Parts Used:
- WP7737P245-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Brocken Burner Knob
This was a simple replacement of a burner knob. The website had exactly what I needed, including a photograph so I was sure it was the exact match. Delivered quickly and was perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from neuvo, CA
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ignitor cracked on 3 of my gas top buners
I used a star head driver to take of burners ,then pulled wires out about 2 inches unplugged old ignitors and plugged in new ones
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Granite Bay, CA
- Parts Used:
- WP7733P410-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
my knob broke
There is really nothing to replace a stove knob. What I was impressed with was the speed in which the knobs came to my house, the very next day from the day I ordered them.
Thanks a ton!
Thanks a ton!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Cresco, PA
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Range would not light.
First I removed the burner, two screws held it in place. The ignitor is attached to the burner with one screw remove the screw then remove the one wire connection. Reverse the steps to put back together. The whole job from start to finish takes about five minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Overland Park, KS
- Parts Used:
- WP74009336
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The ignitor went out on one of the burners of the gas range
Remove the burner cover to reach the burner assembly. From the top of the cooktop you will see 2 screws holing the burner assembly. Using a T drive (6 point screwdriver)remove both screws and the burner assembly will come out of the cook top. Using a phillips head screw driver, remove the old ignitor from the burner assembly. Mine was galled up, so I had to use some penetrating oil and let it sit for a half hour. I then used a hammer and a phillips head screwdriver to tap the screw as I twisted to un-tightened the screw. Once it broke loose, I placed the new ignitor and reassembled the burner into the stove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Half Moon Bay, CA
- Parts Used:
- WP7737P245-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
A plastic handle cracked and was loose.
I lifted off the broken handle and replaced it with a new handle. It worked.
Was this instruction helpful to you?
Thank you for voting!