89889 Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Bill from ROCKLEDGE, FL
- Parts Used:
- WPY700854
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Could not read numbers on the knobs
Simply pull off the old ones and replace with the new ones. Problem was finding the correct knobs with the double "s" shaft fitting.The item number indicated by the model number was incorrect. I saw a kit with four knobs on your web site and ordered the kit and not the recommended item. Turned out to be the right move and the knobs fir just fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Cadiz, KY
- Parts Used:
- WPY700854
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner Knobs worn and bent
Placed new burner knobs onto cooktop. easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Athena from Mill Valley, CA
- Parts Used:
- WPY700854
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner knobs were old and some settings had worn off.
Wrap first three fingers of right around old knob. Pull it off and throw in trash. Take new burner knob and slide it onto the stem. Repeat 3X, that is, once for each remaining burner knob. Time to complete job - 45 seconds. :-D
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barb from Holladay, UT
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replacement
This down draft filter was just what I was looking for. The big box stores (Home Depot and Lowe's) do not carry this size filter. Thanks,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Berlin, MD
- Parts Used:
- WP5700M426-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
grill would not get hot enough
I have a newer jenn air with the 3 prong elements. The original element was 3 prong 1900W only using one of the controls. Since the stove socket would accommodate 4 prongs I looked up the part for the older stoves (PS2357533)which had 2 elemants using both controls. The element plugged right in and I now have high heat like on my older models and it now grills like it should instead of just heating the stuff up. Highly recommended. One caution you will need a metal piece to support the element since the newer stoves do not use the metal bricketts with supports.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kay from Fontanelle, IA
- Parts Used:
- WP5700M426-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old grill burnt out
took new element out of box, inserted it into stovetop, everything was over in about 2 minutes. It worked just fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Candace from Iowa Falls, IA
- Parts Used:
- WPY700854
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Needed to replace the burner knobs on my stove.
Great company....Fast delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janice from Ocala, FL
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Holes in the air filter of our Jenn-Air grill
Simply pulled the old filter out and put the new filter in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn W. from Lake Charles, LA
- Parts Used:
- 700855K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The metal parts of the switches that the control knobs fit on broke on three of the switches.
I removed the two screws holding the control panel in place with a Phillips screwdriver, pulled the assembly of switches up, and found the number on the old switches. Amazingly on PartsSelect's website I found a picture of the exact switch with the exact same part number stamped on it. I ordered three new switches, and they arrived two or three days later. I removed the wires from the old switch with a pair of needle-nose pliers, reconnected them to the new switch in the exact same places, and had all three of them installed and working perfectly in about 45 minutes or an hour.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Lakeville, MA
- Parts Used:
- 700855K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The heat would not stay on keep heating up and turning off with no low heat
Unfortunately it was the wrong part I replaced the infinite switch and had the same problem so I am still trouble shooting but I plan to continue to use parts select they are excellent to work with and very quick to deliver parts
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from Santa Claus, IN
- Parts Used:
- 700855K
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench set
Surface burner did not heat
I ordered part one day, recieved part the next day. I installed it the next day. It worked perfect. THANK YOU!
Was this instruction helpful to you?
Thank you for voting!
Both burners would come on when you turn on the back larg back burner.
Replaced surface unit infinite switch
Was this instruction helpful to you?
Thank you for voting!
stem on burner controls broken
follow the EASY to read and understand instructions.replaced all 4 controls in about 35 min.
Was this instruction helpful to you?
Thank you for voting!
bearing went out in blower motor
removed old motor from cooktop & motor housing & replaced w/ new motor & parts to install same. parts needed where screws & isolators (3).All went ok
Was this instruction helpful to you?
Thank you for voting!