89889 Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Merwyn from Kingsport, TN
- Parts Used:
- 700855K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Bad switch
As stated on order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Flower Mound, TX
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old yucky filter
Thanks, have been looking for a replacement for this dinosaur filter forever. It is great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Montclair, VA
- Parts Used:
- WPY700854
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Numbers on original stove top had become unreadable due to age and needed to be replaced
I originally ordered the knobs that appeared to be an exact match for the ones on the stove top (Part # PS1515077). However those knobs are designed to fit on D post stems. I finally ordered PS48861 which are designed to fit double flat post stems which is what I have on my stove top. New parts fit perfectly. Remove old knobs put new ones on. Total repair time less than one minute. Part Select was great about getting the original parts and replacement to me quickly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Fulton, NY
- Parts Used:
- 700855K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
The stem of one of my burner switches broke off so I had to replace the switch.
Replacing the switch was very easy. First I unplugged the range to be sure there would be no electrical power to the switch. Then I removed four screws to remove the switch cover plate (located above the oven door). I disconnected the wires from the pin connectors on the broken switch, then removed the switch by removing one hex nut. The new switch was installed by reversing the removal procedure. Took about 15 minutes total time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kelly from Alameda, CA
- Parts Used:
- 700855K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
uneven/intermittent burner heating
shut circuit breaker, remove two screws, lift knob panel, move wires to new switch, remove and replace switch, clean surface
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from cairo, IL
- Parts Used:
- 700855K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
front burner would only work on high
Installed the part------very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann from Irvington, NY
- Parts Used:
- WP7772P007-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The paint had chipped and peeled on the inlet grill
I lifted off the old grill and replaced them with the new ones. My stove top looks great again. If I could find them, I would like to replace the knobs to turn on the gas!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janice from Ocala, FL
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Holes in the air filter of our Jenn-Air grill
Simply pulled the old filter out and put the new filter in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Temple Terrace, FL
- Parts Used:
- 700819
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Heat Errosion
Wife installed them, they just snap into place on the Rock Grate.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nancy from Lakeville, MA
- Parts Used:
- 700855K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The heat would not stay on keep heating up and turning off with no low heat
Unfortunately it was the wrong part I replaced the infinite switch and had the same problem so I am still trouble shooting but I plan to continue to use parts select they are excellent to work with and very quick to deliver parts
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Berlin, MD
- Parts Used:
- WP5700M426-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
grill would not get hot enough
I have a newer jenn air with the 3 prong elements. The original element was 3 prong 1900W only using one of the controls. Since the stove socket would accommodate 4 prongs I looked up the part for the older stoves (PS2357533)which had 2 elemants using both controls. The element plugged right in and I now have high heat like on my older models and it now grills like it should instead of just heating the stuff up. Highly recommended. One caution you will need a metal piece to support the element since the newer stoves do not use the metal bricketts with supports.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kay from Fontanelle, IA
- Parts Used:
- WP5700M426-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
old grill burnt out
took new element out of box, inserted it into stovetop, everything was over in about 2 minutes. It worked just fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn W. from Lake Charles, LA
- Parts Used:
- 700855K
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The metal parts of the switches that the control knobs fit on broke on three of the switches.
I removed the two screws holding the control panel in place with a Phillips screwdriver, pulled the assembly of switches up, and found the number on the old switches. Amazingly on PartsSelect's website I found a picture of the exact switch with the exact same part number stamped on it. I ordered three new switches, and they arrived two or three days later. I removed the wires from the old switch with a pair of needle-nose pliers, reconnected them to the new switch in the exact same places, and had all three of them installed and working perfectly in about 45 minutes or an hour.
Was this instruction helpful to you?
Thank you for voting!
Both burners would come on when you turn on the back larg back burner.
Replaced surface unit infinite switch
Was this instruction helpful to you?
Thank you for voting!
stem on burner controls broken
follow the EASY to read and understand instructions.replaced all 4 controls in about 35 min.
Was this instruction helpful to you?
Thank you for voting!