JEC8536ADF Jenn-Air Cooktop - Instructions

I carefully pulled the 3 D rings that were left on the posts of the burner controllers with a pair of needle nosed pliers, made sure there was nothing on the controller posts, then put the new knobs on. Make sure there are no D rings on the oven knob posts, 2 of the knobs were fine, they just didn't have D rings in them. Partselect was great. Items were received within 2 days. I would definately recommend them.

Take old off and put new on

Cut power to range in breaker panel. Then removed two screws (1/4" nutdriver) or phillips head just under top in front. No need to move range out from wall. Once those two screws were out, I lifted the top carefully (since wires are attached to back of range) and propped it up with a piece of spare lumber I had lying around. Then removed two screws holding right rear burner, and doing one wire at a time, pulled the wires from bad burner and reattached wires to new burner. Oh, I did need some pliers to pull the wires from the old burner; they were on real tight. ALSO, the old burner had a series of numbers around it. I quickly learned that these helped you line up the burner correctly. So I noted the numbers with the screw holes in the old burner and made sure I used the same number holes in the new burner. Once new wires were attached, I attached the new burner, aligning the same hole numbers as the removed burner, and everything lined up perfectly. Two screws were inserted to hold the burner. I lowered the top and reinserted the two screws under the front of the top and I was done. Total time was about 13 to 14 minutes. Honestly, very easy. Plus prior to me taking on the project, I had called a Maytag repair shop, who said their fee was $99, plus parts, plus any extra time required for labor, but the latter was not likely something that typically occured.

I removed the split knob and slipped the new knob right on. The knobs look metal but are actually plastic and split over time and use. Really easy to replace. Thanks part select.

Took off the old knobs, replaced with new ones.

The identical knob to replace cracked knob, arrived 2 days after I ordered it on line. It was replaced in minutes and we were very pleased to find this available service.

just replaced the knobs and they were a perfect match,can not tell the new from the old ones. thanks for the prompt shipment

Pulled old ones off and replaced new ones by pushing them on the spindles. Very easy!

I unplugged the stove and removed two screws on bottom of stove top (above oven door) one screw holding burner bracket in place. Took one wire off at a time and hooked to new burner, tightened all screws back down.

My son that is now in the Army National Guard was rather rough on the knobs for the range. Instead of pushing down and then turning, he would just turn the knobs and broke three of them. I only had one left that would operate all of the burners. I searched all over the local area and could not find any replacements for them. I went to the internet and found your site and the exact knobs I needed to replace the broken ones with. I received the new knobs in the mail and then put them on the range. It is nice to have knobs that actually work and it makes cooking much easier.

We lifted the glass top, uninstalled the old burner and installed the new burner in it's place. It worked right away - and is still working. No other tricks the new burner was a perfect fit.

the cracked knob left the round piece of metal that is part of the knob inside the stovetop, preventing the new knob from being installed at the right height. We were able to remove the metal piece and place the new knob on at the correct height. We were very pleased at how fast the part was received.

Pushed the knob down on the spindle. Second order in three years.

bought new ones and pushed them onto D shaped posts total time 90 seconds they may break again in 10 years but I am to lazy to reinforce them

The original knobs were poorly made and kept braking. After the third set, which were very expensive for some plastic knobs, I read this web page for help. Based on what I learned and what I read, I glued the metal sleeve in the knob shaft with some super glue. I then wrapped the shaft with copper wire and spread some industrial glue over the copper wrapping, which looked like a spring around the shaft. I have had no problems in the last month. I hope it keeps up.