JGC9536ADF Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mark from Cordova, TN
- Parts Used:
- WP8286828
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
All ignitors on the cooktop would engage whenever any of the burners were turned on.
Replaced the spark module. Make sure you mark the wire locations on the existing spark module and install them in the same slots.
I was able to repalce without pulling the cooktop out. The access is from the bottom.
I was able to repalce without pulling the cooktop out. The access is from the bottom.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from CONCORD, CA
- Parts Used:
- WP74009336
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Weak spark for igniting gas burner.
Removed the gas deflector; unscrewed the burner body; pulled off the ignition wire; unscrewed the bad electrode; screwed in the replacement electrode; reversed the steps. Voila! Perfect operation once again. My one mistake? Ordered the wrong electrode initially. Make sure you get the right part the first time around.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sid from Saint Francisville, LA
- Parts Used:
- WP7733P410-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plastic Burner Knobs cracked
Pulled off the old and pushed on the new. Took less than a minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jose from san juan bautista, CA
- Parts Used:
- 74007736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
erratic spark from electode,gas would no ignate.
Removed the two fastening screws with a small square head screwdriver,lifted the burner head disconnected wire from damaged electrode. To install just reversed the steps,total time less than ten minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherry from Mentor, OH
- Parts Used:
- WP7733P410-60
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Knobs on the new JennAir Range I just purchased started to melt and when they were called they did nothing about it. I had to call and get new knobs at my cost.
Very easy, just removed the old ones and the new ones just clicked on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from FAYETTEVILLE, GA
- Parts Used:
- WP74009336
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Replaced electrode. Complications heat soldered set screw to electrode
Installation is simple and very straight forward. Problem, was i stripped the torx screw to release electrode because the screw was frozen. I then tore electrode out leaving space to use penetrating oil (inaffective ) then using a chisel to pop the screw out. It came out intact and did not damage the threads in the burner. So what could have been a 20 minutes job, turned into over an hour. But still worth doing myself.
Was this instruction helpful to you?
Thank you for voting!
Igniter clicked but burner would not light
Once I got over my first time jitters this was easy. Lucky for me the old screws went back in just fine. The recommended 8/18 x 3/8 screws were way to small to be usable. Check the length of your existing screws if you can before purchasing the recommended ones.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from WOODLAND, CA
- Parts Used:
- WP74009336
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Replacing burner electrode
This should be a 5 min job. Lift off the burner cover, remove two screws to lift of the burner base and then remove a Phillips head screw that hold the burner igniter in place.
Unfortunately, the screw holding the burner igniter was rusted and it could not be loosened. WD-40 did not touch it. I used a stronger penetrant, "Blaster". Still it would not budge. Then I used a small Phillips head screwdriver and a hammer which I used as an impact driver. I twisted the screwdriver slightly to loosen and hit it was a hammer. Then I twisted the screwdriver slightly to tighten and again hit it with a hammer. After the penetrant and a couple of more tries, the rusted screw finally moved!!!
With no rust, this should be an easy 5 minute replacement. The burner now works great!!!
Unfortunately, the screw holding the burner igniter was rusted and it could not be loosened. WD-40 did not touch it. I used a stronger penetrant, "Blaster". Still it would not budge. Then I used a small Phillips head screwdriver and a hammer which I used as an impact driver. I twisted the screwdriver slightly to loosen and hit it was a hammer. Then I twisted the screwdriver slightly to tighten and again hit it with a hammer. After the penetrant and a couple of more tries, the rusted screw finally moved!!!
With no rust, this should be an easy 5 minute replacement. The burner now works great!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Rancho Mirage, CA
- Parts Used:
- WP7733P410-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Being dumb enough to buy Jenn-Air appliances
I removed the old knob and replaced with a new one from the plastic package. Biggest challenge: opening the new plastic package. It if very nice to know you have many of the parts I will need over the next 20 years.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Sherman Oaks, CA
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Electronic ignitor malfunctioned
First reviewed other review on this repair. Disconnected ignitor system from electrical source (pulled plug); removed 2 screws holding casing in place; removed it from the cooktop; & removed additional screw holding ignitor. Replaced ignitor and reversed the process. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Mesa, AZ
- Parts Used:
- WP7733P410-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Burner nob broken
Popped the old one off and installed the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn S from Edgewater, FL
- Parts Used:
- 74007734
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Electtrode
removed screws that hold burner in place lifted and removed wire connection, reversed attached wire replaced two screws job done,,,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Grenada, MS
- Parts Used:
- WP7733P410-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken knobs
First I removed the old damaged knobs by pulling upward on the knobs. Then I replaced the damaged knobs with the new knobs being careful to align the male and female connection. After installation I tested each burner for proper operation. As a final test, I asked my wife for her opinion. We're happy!
Charles & Dorothy
Charles & Dorothy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anne from Roseland, NJ
- Parts Used:
- WP74007752, 74007422
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Neede new burner caps for cooktop
Nothing mechanical was required! But the service was phenomenal. These are just a drop in part. I was thrilled that you had them, received them in one day without overnight charges, And the cost was very reasonable.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edgar from COCKEYSVILLE, MD
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ignitor sparking at bottom, not the top
Removed two star screws from the top of the burner, disconnected the wire going to the Ignitor, removed the old ignitor held in with one phillips screw, installed new ignitor and re-installed the burner assembly. Simple!
Was this instruction helpful to you?
Thank you for voting!