CVG4280S Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Martyn from Middletown, OH
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The original grease filter was damaged in our dishwasher (it is quite fragile) and needed to be replaced.
1. Remove the exhaust vent cover, located in the center of the top of the range. It just lifts off.
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- alphonso from plainfield, IL
- Parts Used:
- WP71003558
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
blower motor was making loud noise
removed motor, saw that stablizers were broke and went to a local parts supply shop called SUNDBERG and was given a price of about 49.00 for three stablizers. at that point i went to the internet and found PARTSELECT.COM were i found the same parts for a fraction of the price,17.00, i could not believe it! SUNDBERG customer service was horrible.PARTSELECT custormer service is great and was just over the internet,any how the repair is done no more loud noise and wife is happy again ,for awhile.thanks keep up the good work.i tell everybody about you guys.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from Ironton, OH
- Parts Used:
- W10341820
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
defetive fan switch
throw breaker, unbolt switch, unplug leads, rerplace switch, bolt in place, reattach leads, turn breaker back on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yong from Houston, TX
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Change the Oil/Grease Filter
It is so easy. Once I found the right size of filter from the website, I ordered it right away. It came in 3 days and I just need to take out the old one and insert the new one. No instruction is necessary. By the way, the price of the filter is one third of that from Jenn-air.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Escalon, CA
- Parts Used:
- W10341820
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The old switch became brittle with age and broke. There were two plastic cylinders that held a spring loaded bearing to operate the contact point. It became brittle because of age and it broke.
I first turned off the power to the range. The switch was housed inside a control panel in the front center part of the range. Two screws were removed and the housing was lifted forward and then off The switch was held in place by metal friction washers. Those were removed by a screwdriver and then the switch slide off the posts that they were attached to. The switch had two wires and I simply replaced the wires onto the new switch and placed the switch back onto the posts. The friction washers were pressed back over the posts to hold the switch in place and then the housing was screwed back into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melissa from Buford, GA
- Parts Used:
- W10341820
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Fan Switch Broken and being held only by Electrical Wire Connections
removed two screws under fan cover at end of stove knobs. raised panel with knobs up and removed two nuts that held fan switch housing. installed new switch and moved power connections to new fan. (note: Killed power to range top prior to any repair action)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from St. Remy, NY
- Parts Used:
- 1430322
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Burners would not light sometimes
Slide stove out unplug remove cover on back bottom left 3 screws remove wires from old module and plug into new module could not remove old module I glued new to old replaced cover pluged back in slide stove back in and the burners lit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Maplefalls, WA
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Filter replacement.
Remove and replace grease filter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- judy from clifton park, NY
- Parts Used:
- WP7505P283-60, 74005189
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
it was painless
just as stated before. Remove old burners from plate and reattach new burners.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAMES from McALESTER, OK
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
vent fan cloging up
old filter fell into from removing and cleaning,
removed cover pulled out filter ,replaced it with new one.
removed cover pulled out filter ,replaced it with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Katrina from Coos Bay, OR
- Parts Used:
- W10341820
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Fan on built in Jenn-Air went out.
ordered part, called friend who does odd jobs, and he came and turned off electric, unscrewed the area, pulled out old plug, plugged in the new. Turned on electric and walla, fan works !!!! thank you very much. Part arrived in very short length of time. I was surprised.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darrell from Moultrie, GA
- Parts Used:
- W10341820
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
switch too big for hole
switches had same parts numbers but were not the same size. Had to use die grinder and file to enlargh hole. took about 30 min.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Mountain Iron, MN
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old grease filter had hole wore through
Pulled the old one out & inserted the new one. Less than five minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Redona from Roseville, CA
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Worn out stove top
We replaced the burner grates, knobs, air filter and burner pan. Looks as good as new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clark from Tifton, GA
- Parts Used:
- WP7505P283-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Burner wouldn't light.
Took out a couple of screws and put in the new part. PartSelect was fast and efficient. Highly recommended.
Was this instruction helpful to you?
Thank you for voting!