JGD8345ADB Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Bronius from College Station, TX
- Parts Used:
- 8215557
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Intermittent but rare spark when I went to start the rage: spark module definitely was toast or on its way out
The trickiest part was locating the elusive spark module. I am not certain I took the best route, but not considering all the wrong routes in trial and error, it was the most expedient. Certainly there must have been a single something to remove to get to this frequently faulted part..
Anyhow, thanks to the great part, the stove works really well again.
Anyhow, thanks to the great part, the stove works really well again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from MADISON, FL
- Parts Used:
- WP3403M075-10
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Burner Igniter And Burner
Dis mantel burner unit removed burner replaced burner and igniter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jon from bartlett, TN
- Parts Used:
- WP3403M075-10
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
burner head rusted out
undid about 7 screws to get access to underside of burner, unscrewed 4 screws that held on gas feed pipe and ignitor. twisted out old burner and gently removed ignitor from burner. cleanded up area where burner was and installed new one. took a little bit of tweeking to reinsert ignitor but did slide in nicely. reattached gas pipe and all screws. slide burner case back into position. turned on and worked nicely.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Inga from Petaluma, CA
- Parts Used:
- WP74005890
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Only two burners lit
Removed old igniter set replaced with new one. Hardest part was using the screw driver to removing the backing. Saved us having to buy a new stove since we just bough the house.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Arthur from South Burlington, VT
- Parts Used:
- 74004053
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Burner igniter was not lighting the pilot. Needed replacement.
We replaced 3 of 4 igniters on the stove top according to the previously submitted recommendations. Easy to do butt after putting one of the modules back together, we found one igniter still didn't function. We discovered the solution was to run the connecting wire under the gas tubing. Apparently it was compressed when it was over the top of the tube and not under it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bam from Wilmington, NC
- Parts Used:
- W10341820
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
The high/low fan switch was inoperable.
The available replacement switch is a bit too large to fit into the hole on the original face plate which must be kept as it also mounts the 4 burner dials and the “on” light.
A local machine shop was able to make the original hole large enough to accommodate the new switch. Total time to detach and reassemble the original face plate, less than 2 hours. Other than the new switch being black, it looks original. (The 2 smaller face plates provided with the new switch were not needed.)
A local machine shop was able to make the original hole large enough to accommodate the new switch. Total time to detach and reassemble the original face plate, less than 2 hours. Other than the new switch being black, it looks original. (The 2 smaller face plates provided with the new switch were not needed.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Townshend, VT
- Parts Used:
- WP3403M075-10
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Burner heads were rusting through and letting flame leak out
Lots of small metal screws to remove on the housing, gas supply and electric igniters. The only challenge for me was getting the old burner heads out of the trays- they ere rusted up and needed a little penetrating oil and time to break free. I re-used my old igniters- had to bend open the little metal rod at the tip a half of a millimeter to get them to fit back thru the new heads. Keep track of how things come apart and the way the gas lines assemble and it's an easy project. Be careful not to over-tighten old screws in rusty holes in the trays.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robin from saint marys, GA
- Parts Used:
- 74004053
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
2 burners rusted apart, 1 gas valve frozen up.
Removed burner pan screws,igniters, gas tubes & burners. Changed 2 igniters, removed rust & repainted ends of 2 of the tubes (heatproof paint). New burners were made a hair smaller than original but locked in O.K...Now, the hard part...disconnected all four tubes from gas valve assembly. (Had to shut off gas to house in order to remove main gas line to stovetop.) Had to remove valve box in order to remove/replace frozen valve. Unit is 25 years old, works as and looks new...Rust was caused by boil-overs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from Brookeville, MD
- Parts Used:
- WP3403M075-10, WP2001F175-09
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken Burner Head,
Take your time and remove items carefully and replace with new items. Very easy but you definately cant rush and possibly need new screws to make it even easier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Shelley, ID
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broke the insulator on the ignitor while cleaning the cooktop.
Unscrew the bottom cover, remove the old ignitor. Reverse the process to install. Hardest part was getting the bottom cover screws out because of rust. Otherwise, very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cor F. from Pasadena, TX
- Parts Used:
- 8215557
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Screw drivers
Replacement of a Dead Spark Module
The spark module pulses a stepped up voltage to all four burner sparks at the same time regardless of which burner you want to ignite. I read that this part lasts about 10 years. I don't cook much and it lasted 13 years. On my Magic Chef the part is behind the right side wall panel. Lift the range top,remove all the screws that hold the right side panel in place. This replacement can done without opening any gas fittings.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joellen from Castro Valley, CA
- Parts Used:
- WP3403M075-10, 74004053
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner head was rusted through
This is the second burner head I have replaced. It was easier than the first time but the burner head I received did not have the screw holes to reattach the gas tube to the burner head. I was able to drill my own without too much trouble using a standard bit and electric drill. I used the old burner head to determine what size drill bit to use. Even so, it was still an easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Nashville, TN
- Parts Used:
- WP3403M075-10
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
gas burner had rusted out
replaced burner
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from Block Island, RI
- Parts Used:
- 74004053
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken insulator for top burner igniter
I have a Magic Chef gas stove, The top burner came off with ease, just a quarter turn then pull up to expose igniter. Only two wires to remove and two phillips head screws to remove to release igniter. I was done in 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barb from Holladay, UT
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Replacement
This down draft filter was just what I was looking for. The big box stores (Home Depot and Lowe's) do not carry this size filter. Thanks,
Was this instruction helpful to you?
Thank you for voting!