Models
>
JGD8345ADB
JGD8345ADB Jenn-Air Cooktop
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for JGD8345ADB
Viewing 5 of 5
Manuals & Guides for JGD8345ADB
Click to downloadKeep searches simple, eg. "belt" or "pump".
$38.73
This is a genuine OEM replacement grease filter for downdraft exhaust ranges and cooktops. The filter is used to trap grease and particles that result from cooking and will need to be replaced once th...
In Stock
Order within the next 5 mins and your part ships today!
In Stock
Order within the next 5 mins and your part ships today!
$20.77
This is a screw and it is made for multiple appliances in your home. This model is called a sheet metal screw because it has sharp points, and the threads are closer together. This screw is designed t...
In Stock
Order within the next 5 mins and your part ships today!
$5.41
This is a multi-use screw and can be used on a variety of appliances. The measurements of the screw are: 8/18 x 3/8. *Please note: the screw is sold individually. Refer to the manual provided by the m...
In Stock
Order within the next 5 mins and your part ships today!
$158.44
This surface burner head is for ranges.
Surface burner head distributes the gas through holes or slots to create an even flame across the cooking area.
Shut off the gas supply and unplug the ran...
In Stock
Order within the next 5 mins and your part ships today!
In Stock
Order within the next 5 mins and your part ships today!
In Stock
Order within the next 5 mins and your part ships today!
$211.11
This may look different than the original, but is a functional equivalent. When installing this part, you may be required to drill holes and file the metal edges to adapt the switch to the original panel.
In Stock
Order within the next 5 mins and your part ships today!
$45.46
This jar is a little over five inches long. It is made of glass and is used for collecting the grease drippings of gas ranges.
On Order
$8.04
This is the replacement brass seal for your range or cooktop. It is made of brass and is approximately 1 inch in diameter. This part may also be known as the surface burner orifice holder seal. It pre...
In Stock
Order within the next 5 mins and your part ships today!
$132.56
This part sends enough current to the igniter to create a spark to the bottom of the burner cap.
In Stock
Order within the next 5 mins and your part ships today!
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for JGD8345ADB
Viewing 5 of 5Will Not Start
Fixed by these parts
How to fix it
Gas igniter glows, but will not light
Fixed by these parts
How to fix it
Element will not heat
Fixed by these parts
How to fix it
Touchpad does not respond
Fixed by these parts
How to fix it
Gas smell
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- ELOISE from MILFORD, OH
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced filter
pulled old one out , cleaned the area & replaced with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- deborah from fort pierce, FL
- Parts Used:
- WP707929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old grease filter that I actually did not know I had to change
Removed the old grease screen and cleaned the entire area thoroughly and replaced the screen
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- roy from East Providence, RI
- Parts Used:
- 74004053
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
gas burner ignitor failure
Lift out sealed burner assembly rear of stove first while careully sliding to rear to disengage ignitor probes.Remove philips head screws from bottom sheet metal housing to expose bottom of burners Remove gas tube assembly screws and move tube away carefully.Unplug wires from ignitor.Remove screws for ignitor .Remove ignitor, I noticed t
... Read more
hat rust and dirt had built up around burner to pan connection.I used my oil filter wrench to turn slightly the burner to remove it from the pan to clean.Reassembled in reverse order.
Read less
Was this instruction helpful to you?
Thank you for voting!