JGD8430ADN Jenn-Air Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Juan J, from UNIVERSAL CTY, TX
- Parts Used:
- 74007735
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Needed use of penetrate lubrication
Removed two screw securing wburner and disengage igniter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from neuvo, CA
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ignitor cracked on 3 of my gas top buners
I used a star head driver to take of burners ,then pulled wires out about 2 inches unplugged old ignitors and plugged in new ones
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from Overland Park, KS
- Parts Used:
- WP74009336
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The ignitor went out on one of the burners of the gas range
Remove the burner cover to reach the burner assembly. From the top of the cooktop you will see 2 screws holing the burner assembly. Using a T drive (6 point screwdriver)remove both screws and the burner assembly will come out of the cook top. Using a phillips head screw driver, remove the old ignitor from the burner assembly. Mine was galled up, so I had to use some penetrating oil and let it sit for a half hour. I then used a hammer and a phillips head screwdriver to tap the screw as I twisted to un-tightened the screw. Once it broke loose, I placed the new ignitor and reassembled the burner into the stove.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Cresco, PA
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Range would not light.
First I removed the burner, two screws held it in place. The ignitor is attached to the burner with one screw remove the screw then remove the one wire connection. Reverse the steps to put back together. The whole job from start to finish takes about five minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Hendersonville, NC
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ignitor cracked and would not light
Simply removed the old ignitor and install the exact replacement part. Work great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from La Habra, CA
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken electrode
First I tried twitching my nose....after I stopped sneezing I got a screw driver and put the new electrode in and gosh in gahiggy, it worked!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Buena Park, CA
- Parts Used:
- W11087445
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench (Adjustable)
Gas explosion due to bad Gas Pressure Regulator
First step is to turn gas off to cook top and also disconnect power to the unit. Than using a crescent wrench disconnect the gas line going to the unit from the Regulator. Than again using the crescent wrench disconnect the regulator from the bottom of the unit. Next remove the nipple that connects the gas line to the regulator from the old unit. Apply new pipe dope to the threads and screw it into the new one and tighten down. Next install the regulator to the unit and install the gas line to the regulator. once done with the install you can now plug the unit in and turn on the gas. You are now ready to use the cook top again
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Tyngsborough, MA
- Parts Used:
- 814323
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
feet on gas stove top grates were gone
Very simple, cleaned out what was remaining of the old rubber feet and just pushed these in. I didn't bother glueing them in as I didn't feel they would fall out. If they do, I'll go out and obtain the glue that is mentioned by others in this thread. Very satisfied.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Monee, IL
- Parts Used:
- 74007736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burner did not light
Ordered online Tuesday, delivery by FedEx on Wednesday. Removed the old "popped" in the new and it worked right away. It was that simple. Thanks so much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- edward from nanticoke, PA
- Parts Used:
- 74007735
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner porsclend was cracked and would not light
removed grate and cap.unscrewed burner plate.disconnected spark wire and replaced with new part.fired it up .now it workes again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KARL from OCEAN, NJ
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
burner ignator split--
unscrewed old ignator---replaced w new--done deal!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Sanbornton, NH
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burner igniter didn't light burner
I removed the burner by unscrewing 2 torx head screws, disconnected wire from electrode, removed screw holding electrode, inserted new electrode,connected wire, installed burner and fired it up.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Carson City, NV
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Damaged Ignitor
Simply unscrewed the old one and installed the new one and we have ignition!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Boardman, OH
- Parts Used:
- 74007736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Electrode cracked, spark misdirected, poor lighting
After determining it would not be possible to replace the electrode only (rusted/corroded connection), ordered burner head with electrode. Part came in approx. 24 hours. Actual repair involved removing two screws (star-shaped head),disconnecting electrical clip, removing part, connecting electrical clip to new head, reinstalling two screws. Works great now!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Dayton, OH
- Parts Used:
- 814323
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Burner grate pads worn off or missing
I took a jewelers screwdriver and completely cleaned out what was left of the old pads. Then applied a small amount of heat resistant rtv sealant to each hole, slid in the new pads and wiped off the excess. I let everything set overnight. The next day everything was solid. Job was complete. Note I've done this before and did not get the results I did this time. I believe it was the instruction that came with the pads and the tip-off to use the rtv. Thank you PartSelect T.Garr
Was this instruction helpful to you?
Thank you for voting!