Models
>
JGD8430ADN
JGD8430ADN Jenn-Air Cooktop
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for JGD8430ADN
Viewing 5 of 5Manuals & Guides for JGD8430ADN
Click to downloadKeep searches simple, eg. "belt" or "pump".
These pads go on the bottom of your gas cooktop grates to prevent them from moving and scratching the top of your appliance.
In Stock
$41.57
This burner electrode, also known as a burner igniter, is a genuine OEM replacement part for your gas range. When the burner knob is depressed and turned, this part is used to create a spark that ligh...
In Stock
In Stock
In Stock
This is the burner head and electrode for your gas range. If your gas igniter glows but will not light, or if the element will not start or heat entirely, you may need to replace the burner head. This...
In Stock
In Stock
In Stock
In Stock
$92.66
This exhaust vent blower wheel is almost seven inches in diameter, and just under four inches deep. It is made entirely of metal and is used with a range's venting system.
In Stock
In Stock
In Stock
On Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Problems and Symptoms for JGD8430ADN
Viewing 3 of 3Gas igniter glows, but will not light
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Element will not heat
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jeff from Lake Orion, MI
- Parts Used:
- WP74009336
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Wrench set
Ignitor stopped working on gas cooktop
As others reported, there are 2 torx screws that need to be removed so that the burner element can be removed. One came out with a little effort, the other one did not as it was corroded. After breaking a torx bit, a second torx bit succeeded in breaking off the screw head. This then required a drill to drill out the broken shaft and th
... Read more
en rethreading the screw hole. On to the ignitor replacement. The tiny screw holding the ignitor was corroded and would not come out. It too had to be drllled out and rethreaded. It was a 1/3" #4 screw with fine threads. Had to get it an appliance repair store as the local hardware places don't carry fine threaded screws. Finally got it all put back together after a week. My advice before ordering an ignitor is make sure you can take the current burner off the cooktop first to do the repair in the first place. BTW, the ignitor I ordered came quickly and was the correct part!
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sabrina from Mooresville, NC
- Parts Used:
- 814323
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
several grate pads fell out/lost /broke during cleaning
The only real issue was locating the proper adhesive to ensure that the new pads would not fall out. The small insert paper slip in the package noted that a RTV adhesive should be used. After much searching at the home improvement super store, I learned it would be found at an auto supply store. It is black, and is for high temp use. It i
... Read more
s available in a small tube for around $2.00. The RTV is usually used to make gaskets for heat/oil exposure in auto repair. I did have trouble removing a broken stub from a pad that had broken off in the hole. I used an awl to get what I could and push the rest into the hole deeper, then insert a new pad with along with the adhesive.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Loren from San Luis Obispo, CA
- Parts Used:
- WP74009336
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The ceramic insulator on the burner ignitor cracked & the spark shorted so that the burner would not ignite.
Firts I removed the 2 screws that held the burber in place. Then I lifted the burner up & disconnected the wire that connected to the ignitor. Then I removed the one screw that held the ignitor to the burner. I then reversed these steps, replacing the cracked ignitor with the new one, replaced the screw holding it to the burner, then reco
... Read more
nnected wire, returned the burner to the stove and replaced the two screws that held it. All Done!
Read less
Was this instruction helpful to you?
Thank you for voting!