JXDC440R2WH General Electric Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ervin from Dublin, GA
- Parts Used:
- WB2X8228
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Two surface burners did not work
Removed the two screws from the range's top and the rear zinc cover and replaced the two front clip receptacles. It took me 30 min to finish the job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Aurora, CO
- Parts Used:
- WB2X8228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Old Surface Burner Block Kit Disintegrated
Very easy. Followed the video instructions. Unplug stove. Cut old wires. Tape new wires to old wires to facilitate pulling new wires thru old hole to back of range. Removed back cover. Pulled old/new wires thru to back. Removed old connectors. Attached new connectors. Replaced back cover. Screwed new terminal block to front of range at burner. Attached new burner. Plugged in stove. Replaced stove in counter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Salem, IN
- Parts Used:
- WB2X8228
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Bad connection to electric elements
Lifted top, opened back splash, unplugged old wires and replaced with the new ones them connected to new elements
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marvin from McAlpin, FL
- Parts Used:
- WB2X8228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
burner sparked and stopped working
watch the vidio on your site very easy repair!i give you guy's 5 stars out of 5 !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from El Paso, TX
- Parts Used:
- WB30M2
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
heating element would not heat to red hot.
unplugged and installed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Wheat Ridge, CO
- Parts Used:
- WB2X8228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Burner Terminal had shorted out out.
had to pull range away from wall and unplug it so we could get behind to access the rear panel. we then removed old terminal block, by, removing screws from back panel, and one screw from under burner drip pan, inserted, new block, and reassembled. plugged it in to test and burner worked properly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Betty from Fayetteville, WV
- Parts Used:
- WB30M1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the center of the element had broken
just pulled the old one out and replaced with new one. very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jonathan from Lynn, MA
- Parts Used:
- WB2X8228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Connector to burner is out.
Remove old wire and replace new wire into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacqueline A from West palm beach, FL
- Parts Used:
- WB2X8228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Corroded connectors and melted block on an electric stove.
The original GE blocks/wires were color coded to specific burners. The new ones are not color coded since they are sold individually and work with any burner, but they were identical to the originals in every other way. Just remove old blocks one at a time and connect the replacement so that the burner is connected to the proper control. Since the stove age was unknown, I replaced all four blocks to eliminate a repeat of the problem later. The screws holding the blocks and the wiring cover on the stove back require the same small socket wrench; not enough room in some places for an adjustable wrench. It took no more than 20 minutes to replace all four, test the burners, and close up the back wiring panel. The instructional video on the website eliminated my hesitation to tackle this repair. The parts arrived the next day, with no special shipping service requested. WOW. PartSelect will be the first place I go to find what I need for the next fix-it. I'm almost looking forward to something else breaking. LOL. Thanks, PS.
Was this instruction helpful to you?
Thank you for voting!
The large burner was not working. We had tried a part that was not GE and was supposed to be generic to use. That part required cutting the wire and splicing it to the existing wire. When we used it the burner made noise and it sounding like sparking. The terminal block melted.
When we used the GE part and followed the your video for the repair. From that I would have been able to do it by myself but my husband helped me pull out the stove and take off the back panel. He had me hold the wire and he was able to see what place needed to be unplugged and he unplugged it and put the new one on. We tried it and it was heating immediately. I did not need the new burner that I ordered but we will keep it for the next time the burner does need to be replaced. It did not take 5 minutes for the actual repair. But while I was at it I cleaned the sides while it was pulled out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tom from Kensington, MN
- Parts Used:
- WB2X8228
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
The terminal block for a front stove top burner failed
There was an excellent video demonstrating a very good method for replacing the terminal block at Parts Select.. I ran into a problem with the kit. The wires were too short. Instead of replacing the entire wire I needed to clip off part of the old wiring and solder the kit wires to them. I also needed to insulate the connections with electrical tape to prevent them from shorting out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Charlotte, NC
- Parts Used:
- WB2X8228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Two Stove Elements weren't working
Found PartsSelect on the internet. Saw the video for replacing the Surface Burner Terminal Blocks with their kit. Turned a $400 oven replacement into a $25 quick repair, thanks to PartsSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Montgomery,, AL
- Parts Used:
- WB30M1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
welded supports for the surface elements were broken
unplugged the broken elements and plugged in the new ones. Took about one minute. Tools used: hands and fingers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Mayview, MO
- Parts Used:
- WB2X8228
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Bakelite block in the terminal block broke in two.
I can add nothing to the video you furnished on your website. I am generally all thumbs with home repairs - especially anything electrical - but, your video led me right through it. A good experience. We'll do business again.Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Hastings, MI
- Parts Used:
- WB2X8228
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Right front burner connection to burner broke.
Wife repaired it because she got tired of waiting for me:) Hardest part was pulling stove out of cupboard space to get to back of stove. Easy to repair.
Was this instruction helpful to you?
Thank you for voting!