JXDC440R2WH General Electric Cooktop - Instructions

I simply pushed the new burner into hardware. I then tested it to see if it works. . .

I pulled out the heating coil and pushed in the new coil. I turned the stove top on and heard a sound like "dzzzt". I immediately turned off the burner and waited for it to cool, then pulled it out. The part had a burn melt on one side of the end prong. It turns out that the part that the burner plugs into needs to be replaced. Actually, the stove top is over 20 years old and my landlord will have to replace the whole unit. So it turns out that I didn't need to order a surface element after all, but it was very easy to install!

Removed the old and slipped in the new.No problem and it works fine.

Installation took 30 seconds. Your website was easy to use & the part received was just as described. It arrived beautifully wrapped & in just a few days. ABSOLUTELY AWESOME!I will recommend your site to everyone.

Pulled the old surface element out and plugged the new one in. Took all of 45 seconds!!!!!

It's nice to know that one can still get replacement parts for 50 year old stove tops!!!!

Since the unit is a drop-in range I had to remove the heat shield/drip plate to thread the wires from the control button to the receptable. The replacement part wires were to short to make the connection so I have to use some of the wiring from the old receptable to make the connection. That is the reason for using the wire cutter and connecters.

I pulled the old burner out and slid the new one in it's place. Turned on the eye to make sure it worked. Felt heat in a few seconds and turned off.

ordered new surface element and pushed in to conector turned on switch to test and works fine thanks

Just put it right into the receptacle. I want to add...we had gone to our local appliance store and brought home a wrong-size unit. Got online and your website came up. It was easy to find the correct part, ordered it and it arrived 3 days later. I have already recommended your website to 2 of my friends. One very good experience!!!

After checking at local appliance stores and unable to find the bunner I went online looking. I found this site and there it was. I ordered it, received it within two days, took the old one out and the new one in. As my granddaughter says, "easy peasy lemon squeeze". It took all of five seconds and I'm cooking again.

Removed old burner, plugged in new burner. Turned on electric and everything worked fine. I was concerned that I would not be able to get the correct burner since my stove is approximately 30 years old and General Electric no longer stocks replacement parts. The new surface element was manufactured by General Electric and had the correct replacement number on the package. Thanks Part Select.

Replacing the Surface Burner Terminal Block Kit was very easy.

1. Pull the stove from the wall a little so you can have space to work. I unplug the stove from lthe 220 outlet. Then remove the Surface Burner element.

2. Then we removed the back pannel from the stove by removing the screws with a nut driver. Only four screws to remove.

3. Once the pannel was removed. I Unpluged the wires from the stove pannel. Being careful not to damage the plug in. There were only two wires to unplug. So trace the wires to make sure you are unpluging the correct one.

4. Lift the top up on the stove and unscrewed the Terminal Block from the top of stove. We only have one screw there.

5. Pull the Terminal Block and wires out and replace with the new Terminal Block, making sure the wires were feed along the side under the top of stove so they can not be damaged. Plug in wires and replace pannel.

The wire to the burners were old and needed replacement. When the new terminals arrived, my husband had gone hunting. When the parts arrived, I pulled the stove away from the wall and found the nut driver that I needed. I removed the screw on the terminal box under the burner and realized I had to remove the back panel of the stove. I unplugged the old wires and plugged in the new ones. I installed the new terminal boxes under the burners and plugged the burners back in. My stove works like new and I am thrilled that it was so easy. Thanks

Disconnected the electric burner from the terminal block, unscrewed the terminal block, removed the two back covers from the range, cut the two wires (since the wires that came with the replacement part were not long enough to reach the switch), spliced the new part to the existing wiring using wire nuts, installed the new terminal block and connected the electric burner to it. With the new terminal block in place, the burner does not lie completely flat like the old one did, but it is functional.

replace element