JGP933SEK2SS General Electric Cooktop - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Janine from Wind Gap, PA
- Parts Used:
- WB16K10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burnt burner
Just put it on. Quite proud of myself for figuring out what and how to get the part however! The website was very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Salinas, CA
- Parts Used:
- WB03T10242
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Melted the knobs on my range.
Found exactly what I needed and best of all a cheaper version which worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patti A. from Dallas, TX
- Parts Used:
- WB31T10087
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Original grates that came with my cook top had bowed due to the weight of my pans when cooking which caused everything to slide to the back of the pan when cooking.
The grates arrived individually packaged in bubble wrap and in their own box plus those boxes were put in another box with bubble wrap. Very impressed with their shipping technique! The grates fit my cook top perfect! Nothing but good things to say about Part Select and their customer service. Awesome!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anne from Jacksonville, FL
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
After my housecleaner had been here, I noted that 2 of the little rubber feet were missing from the top grates.
I was pretty upset as the grate wobbled, so I went on line and looked for GE Profile parts. To my amazement, I found the little rubber feet quite easily, and within 2 days they were here at my home. I simply had to stick them in the holes; however, I noted that they did not fit real tight, so I removed them and shot a little glue on them, and they have been in place ever since. Thanks to you guys, I am a happy camper now!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Trevor from Eldersburg, MD
- Parts Used:
- WB16K10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner on stove not working correctly
Order parts and installed - no tools needed - completed repairs less than 1 minute
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anne from Plainview, NY
- Parts Used:
- WB29K10024, WB29K10022
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
burner caps began to chip
I removed the two range grills. Then I removed the two chipped burner caps, and replaced them with the new burner caps. I then replaced the two range grills.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Astrid from MORAGA, CA
- Parts Used:
- WB16K10055, WB29K10023
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
THE OLD BURNER HEAD WAS NOT TURNING ON PROPERLY AND THE GAS CAME OUT UNEVEN.
I JUST EXCHANGED THE BURNER AND BURNER CAP.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wesley from FRANKLIN, TN
- Parts Used:
- WB13K10014
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Gas range igniter was making a clicking sound every 3 to 5 minutes, as if it was trying to ignite one of the burners.
Unplug the range from its wall socket to avoid electric shock. The various range parts that support a pot or frypan are easily lifted off their perches, exposing the small white igniter. The only moderately difficult aspect is wiggling the igniter out of its retainer. The electric wire leading into it then can be pulled out and fed into the new igniter with a push. Replace igniter in its retainer, then replace the range parts you removed to expose the igniter and plug the range back into the wall socket. Piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from ABINGDON, VA
- Parts Used:
- WB18T10339, WB13X46909
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Gas coke top wouldn't lite
First step is to turn off the electrical then disassemble the cook top. It is secured to pan by each of the burner mechanisms. Disconnect the spark wire from each porcelain drip pan. Separate the glass top from the pan. If it's stuck gently slide a putty knife int between the two to separate and carefully set the glass top aside. The spark module was a bit challenging in that the colors of the wires didn't match so if you aren't comfortable with electrical work I would get help. The module didn't fit the bracket so,I had to drill new holes and use self tapping screws to mount it. The other part part I intended to change was the spark igniter switch. Unfortunately the wiring was incompatible so I had to return that part. This top was sold by Kenmore but made by GE and is over 10 years old so I suspect an engineering change obsoleted my part. Overall the job wasn't that bad if you are reasonably mechanical..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Solomon A from COLLEGE PARK, GA
- Parts Used:
- WB16T10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
The eye would not light
Remove the existing burner and install the replacement.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- steve from BEAVERCREEK, OH
- Parts Used:
- WB18T10339
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Igniter constantly ticking ...
Unplug!!
Pull knobs
Pull burner centers
Unscrew the nut at the center of each burner
Tilt cover up revealing under burner controls
Remove old harness
Install new harness
Reassemble in reverse order
Plug in NO ticking
Pull knobs
Pull burner centers
Unscrew the nut at the center of each burner
Tilt cover up revealing under burner controls
Remove old harness
Install new harness
Reassemble in reverse order
Plug in NO ticking
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elayne from MEDINA, OH
- Parts Used:
- WB03T10242
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
1 old knob broke on the inside of the knob.
Replaced all 4 knobs. Pulled the old knobs off and put the new knobs on. Easy, Peasey.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sam from Austin, TX
- Parts Used:
- WB13X27058
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Replacing ignitor
Got ignitor and it did not have wire attached as shown in the picture of parts. However, all I did was take burner cap off, and gently life ignitor up and out, detach the wire, attach new ignitor to wire and reset.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Akshay from Bridgeton, NJ
- Parts Used:
- WB16T10046
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Burner had uneven flames
Too easy a five year old could do it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Stratham, NH
- Parts Used:
- WB02T10461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
feet keep falling off
Inserted the grate foot into the spot provided; after consulting the parts manuel to insure I was using the proper procedure.
I do use silicone to help hold the foot but it still won't hold
I do use silicone to help hold the foot but it still won't hold
Was this instruction helpful to you?
Thank you for voting!