Models > JGP933SEK2SS > Instructions

JGP933SEK2SS General Electric Cooktop - Instructions

Jump to:

All Instructions for the JGP933SEK2SS

Customer:: Jesse from Nashville, TN
Parts Used:: WB13K10014
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins

Large burner wasn't lighting very quickly

Removed grill grates, gas distributors, etc. (just lift off). Used star screwdriver to remove screws (3 per burner for SML, 2 for power burner). Lift off stainless cover, which also lifts off the white sparkers I was replacing. Pull them off the wires (didn't need pliers, others said they did). Replace (make sure it is all the way on) and reverse your steps. White sparkers electrodes seemed loose when I put them back on, but tightened up when I fully secured the top back on. Make sure the wires aren't pinched underneath when you put the top back on. Recommended: If you've got one that isn't working, go ahead and replace all 3 (power burner is different) because the part is so cheap you may as well just do it now.

Was this instruction helpful to you?

Customer:: Joan from Warren, NJ
Parts Used:: WB02T10461, WB29K10023
Difficulty Level:: A Bit Difficult
Total Repair Time:: 15 - 30 mins

Both items needed to replace broken or non existent ones

The burner cap was a no brainer. The grate feet should have been also, but many of them were undersized so we had to maneuver them in such a way that they didn't fall out of the grates.

Was this instruction helpful to you?

Customer:: Barbara J from Sweetwater, TX
Parts Used:: WB02T10461
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers

Missing grate foot.

Ordered by phone parts & very pleased with all of transaction.

Was this instruction helpful to you?

Customer:: Jerry from Danville, IL
Parts Used:: WB18T10339
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Screw drivers

igniter kept igniting

Simply removed the 9 T9 screws from the top of the cooktop, removed the igniter spark modules, lifted the top of the cooktop up and removed harness assembly. Unplug harness from spark module and replaced in same fashion. SUPER EASY done in less than 15 minutes

Was this instruction helpful to you?

Customer:: Vincent from Leesburg, VA
Parts Used:: WB18T10339
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Screw drivers

One Burner would not light when using the corresponding knob..

Good way to tell/verify what your problem is. On my GE Cooktop, moving any of the knobs to light cause a spark for all igniters. One of our knobs would not cause a spark. - Remove gas grills and covers. - Remove screws - Pull igniters up (be gentle to not crack them - Pull wire out from igniter - lift cover of cooktop - pull harness off each know and disconnect two wires - put new harness on and connect and backfill. Pretty easy overall.

Was this instruction helpful to you?

Customer:: Ken from Mandeville, LA
Parts Used:: WB18T10339, WB13X46909
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Nutdriver

Constant Sparking on front burners

Easy to replace - caution to make sure spark igniter switch is aligned and secured in correct position on the gas valve. The switch should cover both mounting screws on the gas valve when properly installed/aligned

Was this instruction helpful to you?

Customer:: Olegario from Whittier, CA
Parts Used:: WB18T10339, WB13X27058
Difficulty Level:: Easy
Total Repair Time:: 15 - 30 mins
Tools:: Pliers, Screw drivers

Ingiter Switch shorted; needed to be replaced

TURN OFF GAS and unplug stove. Removed burners (used screw driver to remove screws) and spark ignitors (used pliers). Lifted top cover of stove and unpluged the harness assembly(pulls out easily). Inserted new harness and replaced cover. Replaced burner parts included new spark ignitor. Plug power cord and turn on gas.

Was this instruction helpful to you?

All Instructions for the JGP933SEK2SS