AKT3040SS (10) Amana Cooktop - Instructions

Removed glass top from stove by taking out hex screws which secured glass top to stove frame. There are two phillips head screws inside the exhaust as well. Removed two phillips head screws which hold the burner switch in place. With a sharpie pen I marked the color coded wires on the faulty switch. Removed wires from the faulty switch. Replaced new switch using the old switch as a guide to insure that wires were connected properly. Secured new switch and glass burner top reversing above procedure. Problem solved. Note: The white dot on the control knob did not line up properly with the off position. Black out white dot and make a new one in the proper spot on the knob.

Raised the unit and blocked it with 2 boards. TURN OFF THE POWER IF YOU WANT TO COMPLETE THIS REPAIR. Removed the philip head screws for removal of glass top. Remove the corner screws on switch end. Remove screws holding the switch. Remove screws holing the bracket for all switches. Lift and roll gently to get at wiring. Follow the directions for moving wires from old switch to new switch. MOVING WIRES IS THE MOST IMPORTANT STEP. Reverse your procedure to put back together and when finished remember to turn on the power.

removed 2 screws holding top in place witch gave me ac access to none working part. removed 5 screws witch let me remove part, reversed order to reinstall part, very easy
Donald Carpenter

My cook top has the red wire piggybacked along all the cook top switches. It was easy enough to reroute the red wire coming from the dual surface burner to pin 4 i believe on the new switch. Follow the previous thread and look at the instruction sheet online for this switch

IMPORTANT WIRE CONNECTIONS: The manufacturer instructions describing where each wire connects is woefully incomplete. There are 6 or 7 wires to connect and only 2 are explained in the instructions. I took several photos of the original switch showing where each of the wires was connected before disconnecting and installing the new switch. If I hadn't taken the photos I would have been completely lost on where each wire connected.

raising the cook top on to 2x2s, one on each end, allowed me to remove the 9 sheet metal screws that keep the glass top fastened to the box containing all of the heating elements and controls. After removing the control knobs and the glass top, everything was clearly visible. Removing the four screws that hold the control box frame in place allowed me to turn the switches upside down and photograph the placement of all of the wires on the pins. I then transferred the wires from the old switch to what I thought were the corresponding pins on the new switch(the replacement switch has more pins, and they are not located in exactly the same spots as the old switch). When I turned the power back on, the switch turned the burners on, I had heat but the indicator lights didn't work. I turned the breakers back off and rewired according to a previous commentors wiring directions(his model was not exactly the same as mine), the indicators worked but I was back to no heat. I called my son, who has his own commercial electric company,and he looked at my photos from before, the diagram that came with the new switch, and it took him about 15 minutes to reconnect the pins to different wires and when we turned the power back on---both indicators and heating elements worked. It was the dual switch and double indicator that made it more complex to figure out. Nice to have very smart kids.

Followed Igor’s instructions and it was very easy and straightforward. New switches work great.

I followed your excellent service instructions.
This was the reason I purchased the part from you,
even though other websites had the same part for considerably less

Couldn't hook up the wires since the instructions were so cryptic. Ended up fixing old control and re-installed it. Worked fine.

Here is what I did with new switch (part#12002125) and it worked. Connect jumper to P1 and S1. Split the 2 red wires and put new spades on the ends, then put the red wire from left front switch on P2 and the other red wire from the right rear burner on 2. Blue goes to 4. Purple goes to 4A. Black goes to P1. Orange goes to S2.

the burners were located underneath the glass top, but i had no instructions on how to remove the glass top, so i spent an hour taking every screw off. finally i realized the glass top lifts off from the front then the repair became super easy. hard part was replacing all the screws, lol

Turned off power, disconnected wires, cut tape on exhaust fan connection, removed cooktop from counter and removed glass top from assembly, removed screws on switch, switched wires from old switch and installed on new switch, reinstalled everything, restore power and checkout new switch positions. Everything worked.

Pulled range away from wall and unplugged it. Pulled smoothtop out a bit to clear retaining clips. Swung top up and unplugged the cable going to top. Removed top hinge so top could be removed. Put top upside down on a table to work on. Removed wires from bad burner and then removed screws holding the burner in place. Replaced bad burner with new one and reversed the previous steps. Range worked like new. PartSelect service was great, received the part in one day.

Thanks to the highest rated user comment and following his instructions the switch exchange was easy. The supplied instructions were of little to no help and confusing. The hardest part was getting to the two side top Phillips screws because the granite counter top was in the way necessitating raising the stove till the screw heads were exposed. Once raised the front cover was easily removed after undoing six screws. The cook top did not need to be removed. Either of the supplied wires would work and only one of the two was needed. The replacement switch performed far better than the original.

Move stove away from wall to allow working on back of stove. Unplug stove. Remove metal cover from top rear of stove. Pull control knob off of control (front of stove) Remove 2 screws holding infinite control in place (front of stove) Replacement control not identical to original control, having more terminal lugs and different physical arrangement. I used the terminal letters as a guide for placement of wires. The letters were not exactly the same, but close enough. Re-attach control to stove with 2 screws. Re-attach back metal panel to stove. Shaft on replacement control is smaller diameter and different shape from original, so I removed ribs from inside of control knob hole and then squirted a small amount of hot glue into the hole. Smearing a small amount of cooking oil onto shaft of replacent control I then slid the control knob onto the control shaft, holding it in place until the glue cooled and set. Plug stove back in, and return stove to its position next to the wall.