11931012790 Kenmore Canister Vacuum - Instructions

Removed top of dryer and front panel per instructions and removed belt and drum. After removing what was left of the old rear drum seal I scraped off and sanded the old adhesive off. Reapplied new adhesive and installed new seal after about 3 to 5 minutes (let adhesive get tacky) I then used about a dozen spring clothes pins to hold seal in place while adhesive set up. Reinstalled drum,belt,front panel and top and job was complete. Time included letting adhesive set up. Easy and inexpensive, thank you parts select.

flipped top up, removed 2 5/16 screws and removed front face. removed drum and belt. removed retaining clips on rollers and removed wheels. replaced all clips and new wheels and installed new belt on drum and reassembled in reverse order

Watched video on You Tube, ordered parts online and used excellent instructions sent with belt and other parts in kit. Turn power off by unplugging cord, lift out lint screen, remove screws in lint screen slot, pry up top of dryer with wood chisel or heavy screwdriver, unplug wires top front of dryer, remove self-tapping screws holding front panel in place, lift out drum, remove and replace all parts included in kit, lifted drum back into place, placed detergent bottle under drum to hold it in place while attaching new belt, asked wife to hold lightweight drum in place while I reattached electrical wires and front of dryer. Lowered top of dryer into place and reinstalled lint screen, Be careful! Panels are thin and cut like a knife. Also the dryer lid can fall if you slide the dryer into the wall while working below.

First off, I was somewhat misled by the website and ordered the wrong parts. I entered my model number and ordered the maintainance kit. The info said it was good for Whirlpool, Maytag and others. I also watched the video which is apparently the Whirlpool. So, the wrong parts arrived. The PartSelect peeple were very helpful in getting me the right parts and getting them delivered promptly. I then found the proper video, watched that and did the repair. Be aware that all models have subtle differences. Mine had two long screws in the bottom of the door frame not shown in the video. I also had a little trouble with the pulley spring. I removed the assembly and then got it all back together ok. Then I lost one of the door hinge screws. It evaporated. The replacement part was like $4 so I used one from the local HD and all is well.

I took off top of drier completely making sure to photograph wiring diagram for timer, then removed front. Laying drier on it's back, I could then install new belt and tensioner without needing a second pair of hands. I tried using bungee cord but found it easier for me to lay drier on its back. I completely vacuumed all areas including back of drier. I found the retainer clips for front of drier to be bent, so I straightened them. I also installed two sheet metal screws in case one of the retainers failed.

Remove the lint filter. Remove top without disturbing control wiring -- turn top on end but make sure it cannot fall. Unhook contacts on door switch. Remove screws hloding front panel and kick plate. Remove door hinge springs. Remove front panel and kick plate.Fish out old broken belt. Remove drum. Vacuum out all the lint. Reposition/replace pulley assembly and wheels. Place new belt around drum. Reinstall drum being careful to properly position the seal at rear. Prop up the drum with a suitable sized article to keep it in position temporarily - or have someone else hold it in position. Thread drive belt through pulley assembly per directions and put over drive hub. Manually turn drum to ensure proper belt and seal positioning. Put front panel back on. Turn drum while inspecting seal -- use putty knife to slip under seal if necessary to ensure its not folded under drum lip. Remove the prop holding up drum. Reinstall door hinges springs.Reinstall kick plate. Reinstall top.

Replaced belt,wheels,idler arm and drive motor.Used video instructions from PartSelect.Instructions are spot on.All replacement parts were correct ans fit like a clove.Orderinig was esaey.Staff was friendly and knowleable.Parts arrived quikly with out using next day service.I will use PartSelect in the future and recomend the company to my coworkers and friens.

Poped the top; removed the front of dryer; removed the drum; replaced the rollers and clips, new belt, and new idler pulley. Cleaned out all the lint. Reinstalled all. It works perfect. Ordering the parts was easy and the assistance you give in diagnosing the problem was excellent.

Ordered a parts kit with belt, tensioner, rollers, & clips, but did not use. Unfortunately, the kit was not correct for this model, regardless of the sales reps assurances. The kit had two rollers, our unit has four. The belt tensioner was not even close to being the same. However, a thorough cleaning of the interior with vacuum and rag was done. Removed, cleaned, and lubed each of the four rollers and the tensioner wheel as well. Lubed with small amounts of sewing machine oil on the axles and light spray of silicone on plastic to plastic contact points. Voila! It's as quiet as new.

Parts in the maintenance kit (other than belt) did not fit this old dryer. Top up and front off (door did not have to be removed) drum removed without any problems, pulley in back of dryer. Lots of lint removed, this dryer, must be at least 25 year old, runs great!!!

I tore down the dryer, to find any and all issues. The belt was worn, the rear support wheels were worn, the Blower Wheel was cracked and busted, the left felt support was absent, the right felt support was shot, the water tube leading to the steaming chamber was split in two and disconnected. Ordered all parts from here, they shipped VERY fast, and the hardest part is getting the drum back in and set right. The belt was fairly 3easy to put back on if you removed the water tube support and get your right hand all the way back in there so you can pull the pulley wheel back while holding the belt. Completely cleaned the cabinet out, vacuum and scraper. Put a new exhaust hose on while I was at it, just in case. Once everything was put back together, carefully, the dryer works as good as new. I was told to never get rid of this dryer, they quit making them, and I see why. Easy to repair, does my dress clothes in the top cabinet, dries like a commercial machine in the lower. Oh some installation notes...The front panel comes completely off, if you disconnect the ground and the yellow wire on the lower right (your right) side. This makes everything else much easier. There are 4 front panel screws, 4 edge screws, and four counter screws inside the upper cabinet that must be removed. I had to pull the side holder screws to removed the top plat so I could remove the drum. Keep track of your screws!!! You will need a flathead, a Phillips, a small socket (I forget what size), and some needle nose pliers to remove clips (from the wheel).

The instructions were easy to follow and the pulley on the replacement part was evenbetter quality than the original. I also followed the recommendation to clean the lint trap. Now the dryer works quieter and better than it ever did. Thanks for your product!

Found right parts for problem on this website. Handyman took down machine and installed the drum support wheels. Taking apart was not too difficult; getting drum and dryer face aligned properly was a bit difficult and took longer than expected (and 3 of us). However, it was much better than having to buy a new dryer, since there was very little really wrong with this one. BTW, it was "out of warranty" so it would have cost around $150-$250 to repair using the repair service from the retailer we bought it from. Saved lots of money. Thanks.

I followed instuctions, also watched a how to vidio, had a little problem reinstallig front cover. The job took a little over a hour. The squeel was coming from old style belt tensioner.

Repair was as straightforward and simple as the videos implied. The most difficult part of the repair was disconnecting the door wiring. It could be more plainly shown in the videos. After that it was simple. The cleanup inside the dryer, lint, etc., took as long as the repairs. An extra set of hands to hold the drum in place while routing the new belt over the drive pulley would have made it even simpler. Runs like a new dryer now.