11931012790 Kenmore Canister Vacuum - Instructions

it was easy all the parts were the exact replacement

Found a DIY video clip on YouTube...Ordered the parts...I only needed a replacement belt but PartSelect had an upgrade kit that included not only the belt and rear drum support wheels, but also the tensioner arm with a WHEEL instead of just the flat metal belt guide ( which I believe lead to the belt wearing out in the first place) All the parts fit perfectly and now it's better than new.

Belt was worn, rollers were sticking, idler worn out. Ordered a kit to care for these issues, as usual the reapirs took almost no time. Dryer became a bit quieter for a first load, second load the motor siezed. I priced rebuilding most of the machine and determined replacement was due.

Remove the lint filter. Remove top without disturbing control wiring -- turn top on end but make sure it cannot fall. Unhook contacts on door switch. Remove screws hloding front panel and kick plate. Remove door hinge springs. Remove front panel and kick plate.Fish out old broken belt. Remove drum. Vacuum out all the lint. Reposition/replace pulley assembly and wheels. Place new belt around drum. Reinstall drum being careful to properly position the seal at rear. Prop up the drum with a suitable sized article to keep it in position temporarily - or have someone else hold it in position. Thread drive belt through pulley assembly per directions and put over drive hub. Manually turn drum to ensure proper belt and seal positioning. Put front panel back on. Turn drum while inspecting seal -- use putty knife to slip under seal if necessary to ensure its not folded under drum lip. Remove the prop holding up drum. Reinstall door hinges springs.Reinstall kick plate. Reinstall top.

Replaced belt,wheels,idler arm and drive motor.Used video instructions from PartSelect.Instructions are spot on.All replacement parts were correct ans fit like a clove.Orderinig was esaey.Staff was friendly and knowleable.Parts arrived quikly with out using next day service.I will use PartSelect in the future and recomend the company to my coworkers and friens.

I watched your video that showed me how to remove the top then the face of the dryer. I then removed the drum and belt,after which I could then remove the support wheels and the belt tension wheel.I replaced the support wheels and tension wheel,the hardest part was removing the little plastic locking keepers that hold the support wheels in place. After that I was able to reinstall the drum with the new belt and reinstall the face and top of the dryer. My 15 year old dryer works great just like new. Thanks

Watched repair video first to access problems and steps to do replacement for parts. Took more than :30 only because most of the time was spent cleaning. Amazing how much dirt and dust accumlates inside a closed unit. Even took the back off to clean and check electrical connections. Parts were exactly as shown and explained. Would absolutely use PartSelect again if needed.

Ok, there was a couple of other parts not on the video but were not hard to deal with. I would suggest talking a photo of the assembled parts before taking parts of for a reference when reassembling.

Viewed online video and written instructions that were included in maintenance kit.

Followed the procedure outlined in instructions included with maintenance kit. My dryer did not have a pully wheel on the idler arm. Instead it was more or less a wear bar formed in a semi circle attached to the idler bar. This is what was causing the noise. The dryer wheels were good and the dryer belt was good too after 10 years of use. The parts in the kit were of good quality and fit perfectly. The supplied instructions were easy to follow.

Everyone said changing a dryer belt was a piece of cake.They did not tell the truth it is a difficult job. I am a 52 year old female and I had a problem. You have to take the whole drum out. I finally completed the job but i had to prop the drum up with blocks so I could screw in the front panel. I think for those who want to change the belt I would go smoother with two people so the can hold things in place while the other one screws the panels back. I also think taking the dryer door off make the front panel a lot more easier to put in palce.

Kit arrived with all the parts required and with detailed instructions. LOL... the very specialized tool you will need to dis-assemble the dryer? A PUTTY KNIFE. All in all, aside from the top of the dryer slamming shut without warning and scaring the pants off me, this was a relatively easy repair from a technical level. Only real difficult thing was removing and then restoring the drum and that was more due to clearance than actually being difficult. Make sure once you're finished to LEVEL THE DRYER. That makes a HUGE difference!!!!!

I purchased the maintenance kit and followed the video on part select.com. Replacing the drum wheels, pully and belt was not difficult. I probably found enough coins in the dryer to pay for the maintenance kit. The only tricky part was getting the cap on the end of the axle. It requires a bit of force applied evenly.

Ordered entire Maintenance kit - good call because it was the tensioner pulley that failed and cut the belt. To replace, had to raise the top (2 screws in lint screen slot)and pull the entire front off (2 screws - 1/ea on top inner edge of front door panel then lift it up and out) Replaced both rollers, then used the parts kit shipping box to prop up the front of the drum while installing the belt and tensioner pully. Re-assembled in reverse order, works fine.

Followed instructions that came with part.