See part 25 in the diagram
( Grid squares measure 1x1 inch )
Gearcase
$
226.49
In Stock
In Stock
Fix Number: FIX341974
Manufacturer #: 3360629
Manufactured by:
Whirlpool
-
Product Description
This is used in your direct drive washer that has a neutral drain.
-
Works with the following brandsWhirlpool, Kenmore, KitchenAid, Roper
-
Works with the following productsWasher, Washer Dryer Combo
-
Fixes the following symptomsPumps but will not spin, Will not agitate, Noisy
-
Part Number Cross ReferencePart# 3360629 replaces these:
Product Description
This is used in your direct drive washer that has a neutral drain.
-
Works with the following brands:Whirlpool, Kenmore, KitchenAid, Roper
-
Works with the following products:Washer, Washer Dryer Combo
-
Fixes the following symptoms:Pumps but will not spin, Will not agitate, Noisy
-
Part# 3360629 replaces these:
Videos For installing this part.
Replacing your Gearcase
Replacing your Gearcase
Installation Instructions Provided by Fix customers like you.
Average Repair Rating: 3.6 / 5.0, 3 reviews.
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
-
Customer:Paul from Mobile, AL -
-
Difficulty Level:Very Easy -
Total Repair Time:30 - 60 mins -
Tools:Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
would not spin
well i replaced a lot of parts..but i think it was the the lid switch. but now its brand new..Thanks
Was this instruction helpful to you?
Thank you for voting!
-
Customer:Cory from Sherwood, OR
-
Parts Used:3360629
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
23 yr. old machine had a rythmic thump sound.
Suspected the clutch, but turned out to be worn out nylon gear in the gear case. After compairing the cost of replacing the gear and related pieces a new assembly was more cost effctive.Disconnected the power. Removed the agitator from the main drum. Tilted the washer at a 45 degree angle against the wall to gain access to the pump/motor/gear case Assy. below the drum. Unclipped the pump and pushed to the side. Disconnected the motors electrical connections and removed the three mounting bolts that attach the gear case to the washer and removed the assembly from the washer. Replaced the gear case and reassembled. Unit works perfect.
Was this instruction helpful to you?
Thank you for voting!
-
Customer:Jeffrey from Issaquah, WA
-
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set
Noisy during operation. I found oil on the floor under the washing machine.
Slow gear case leak was at the input shaft seal. I followed the gear case video instructions which are quite good. However the video says you can buy the needed spanner for the tub nut here on this site. I sure couldn't find it and had to order from elsewhere. In this case a TB123A fit well. Upon testing I had a noise when the pump was running. I discovered that I missed aligning one pump leg to the recess. After I released the pump clamps, and slightly repositioned and re-clamped it was fine. The upper agitator was replaced due to slight wear on the internal teeth. The original agitator bolt's intrinsic rubber seal (bolt, washer/seal all one piece) was worn so I replaced that too.
Was this instruction helpful to you?
Thank you for voting!
Model Compatibility
This part works with the following models:
Fix Number: FIX341974
Manufacturer Part Number: 3360629
Manufacturer Part Number: 3360629
Brand
Model Number
Description
Kenmore
10682872600
Washer
- Kenmore Washing Machine Model 106.82872600 (10682872600, 106 82872600) Parts
Kenmore
1101050299
Washer
- Kenmore Washing Machine Model 110.1050299 (1101050299, 110 1050299) Parts