OEM General Electric Refrigerator Evaporator/Condensor Fan Grommet [WR02X10098] | Ships Today | Fix.com
Evaporator/Condensor Fan Grommet – Part Number: WR02X10098
( Grid squares measure 1x1 inch )
Evaporator/Condensor Fan Grommet – Part Number: WR02X10098 Evaporator/Condensor Fan Grommet – Part Number: WR02X10098 https://fixcom.azureedge.net/Schematics/GE/00119164i06.gif

Evaporator/Condensor Fan Grommet

Your Price
$5.00

Fix Number: FIX284555

Manufacturer #: WR02X10098

Manufactured by: GE

Part description

This evaporator fan motor grommet, or condenser fan grommet is built for refrigerators. It provides a cushion between the fan motor and the motor mounting bracket. It is made or round, black plastic and is approximately one inch in diameter. If your grommet is torn or damaged and you are getting noise from the fan motor, you may need to replace it. This is an OEM part sourced directly from the manufacturer.

Works with the following brands

General Electric, Hotpoint, Kenmore

Works with the following products

Refrigerator

Fixes the following symptoms

Noisy | Fridge too warm | Freezer section too warm

Installation InstructionsProvided by FIX customers like you

Average Repair Rating: 3.4 / 5.0, 3 reviews ?
Sort by:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Scott from Nampa, ID
Parts Used:
WR60X10220, WR02X10098
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver
Fan was rubbing against fan shroud and running slow. Rubber gromets were worn and allowing fan motor to sag.
Unplugged the refrigerator. Pulled rear access plate off (removed 7 screws). Disconnected fan motor. Fan motor was running slow even if the fan propeller was clear of fan shroud. Removed two screws to remove the fan motor from mounting bracket. With fan motor loose, I removed the fan propeller from motor by pulling it off the shaft. I then slid the motor shaft out from the mounting bracket to remove fan motor. I then vacuumed out the condenser coil area to remove dust. I cleaned the fan propeller. Removed rubber grommets from motor mounting brackets and replaced them with new ones. Slid new fan motor shaft through mounting bracket and maneuvered motor so as to attach the fan propeller. Reattached fan propeller by pushing it back onto the motor shaft. Fitted motor into the mounting bracket and secured to coil housing with the two screws I removed earlier. Make certain that the grounding wire is secured under one of the mounting bracket screws. Plugged the refrigerator back in. Observed that the fan was rotating free and clear of fan shroud. Reattached the rear access plate.
2 of 2 people found this instruction helpful.
Were these instructions helpful?
Customer:
Michael from Asheboro, NC
Parts Used:
WR60X10170, WR02X10098
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver
Refrigerator was making a squeaking / squealing noise at certain times
Researched possible cause on YouTube determining it could possibly be the condenser fan motor. Relatively easy to remove and replace after watching YouTube videos. Approximately 30 minute repair time
1 person found this instruction helpful.
Were these instructions helpful?
Customer:
Alfred E. from Bloomfield, NJ
Parts Used:
WR02X10098
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
Loud Noise
I watched the video that this site has online. First shut off the power by pulling off the electrical line. If I hadn't watched the video I would have replaced the fan too instead of just the two grommets. I also probably wouldn't have seen that there are 2 grommets, as one of them is kind of hidden in the back of the fan. Also, getting the clip that secures the fan off and back on is not easy. Needle nose pliers are needed and even with those it is not as easy as the video repair man accomplished it. I found expanding the round clip a little made it possible to get it back on. I also put a little Vaseline on it so it slipped back on. Be careful not to damage the fragile styrofoam when you are removing the plastic shield at the start of the project. Go slow. If you damage it, duct tape may help to repair it. You can do this job. Also don't loose or drop the screws.
0 of 1 people found this instruction helpful.
Were these instructions helpful?

Model Cross Reference

This part works with the following models:

Fix Number: FIX284555
Manufacturer Part Number: WR02X10098
Brand
Model Number
Description
General Electric
31181-1
Refrigerator
General Electric
31191-1
Refrigerator
General Electric
3210-00L0S00-A
Refrigerator
General Electric
3210-00R0S00-A
Refrigerator
General Electric
36211XBMBRWW
Refrigerator
General Electric
36211XBMDRWW
Refrigerator
General Electric
36211XBMERWW
General Electric
36211XBMFRWW
General Electric
36211XBRERWW
General Electric
36211XBRFRWW
Kenmore
36348042891
Refrigerator
Kenmore
36348042892
Refrigerator
Kenmore
36348042893
Refrigerator
Kenmore
36348042894
Refrigerator
Kenmore
36348042896
Refrigerator
Kenmore
36348042897
Refrigerator
Kenmore
36348047891
Refrigerator
Kenmore
36348047892
Refrigerator
Kenmore
36348047893
Refrigerator
Kenmore
36348047894
Refrigerator
Kenmore
36348047896
Refrigerator
Kenmore
36348047897
Refrigerator
Kenmore
36348252891
Refrigerator
Kenmore
36348252892
Refrigerator
Kenmore
36348252893
Refrigerator
Kenmore
36348252894
Refrigerator
Kenmore
36348252896
Refrigerator
Kenmore
36348252897
Refrigerator
Kenmore
36348257891
Refrigerator
Kenmore
36348257892
Refrigerator