This is the replacement light switch for your range. It comes with the actual switch, and the hex nut that goes with it. The switch is approximately 1 ¼ inches by 1 ¼ inches, and the hex nut is approximately ½ an inch in diameter. When you press the switch, it allows you to turn the range light on and off. If the light does not come on when you hit the switch, you may need to replace it. Be sure to disconnect your microwave from the power source before you begin this repair. This part is an authentic OEM part sourced directly from the manufacturer.
Works with the following brands:
General Electric
Works with the following products:
Range Hood
Part# WB24X10130 replaces these:
AP3754330, 1086019
Works with the following brands:
General Electric
Works with the following products
Range Hood
Part Number Cross Reference
Part# WB24X10130 replaces these:
AP3754330, 1086019
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
1 question answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched. Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Kathy
November 23, 2023
Replacing the light switch but old one fell off before I saw where each wire went. I have black, blue, and yellow wires. Switch has slots labeled L, 1, 2 and 3. Which wire goes in which slot?
For model number JV348L2SS
Hi Kathy, thank you for contacting us. L is normally the "line" which is "hot". The other numbers are the different speeds, so you will have to try them for the high, medium, low, etc. You should be able to try each to determine which is which. We hope that helps!
Was this helpful?
Thank you for voting!
Related Parts Additional or alternate parts to consider.
This is the replacement fan switch for your range hood. When you turn the knob to turn the range fan on, the fan switch is actuated. If your fan will not turn on when the knob is turned, you most likely have an issue wit...
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
Affresh dishwasher Cleaner is specially formulated to help remove limescale and mineral build-up that can be unsightly and could affect your dishwasher's performance. Each tablet is designed to clean inside your machine ...
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
Turn off circuit breaker to vent hood. Note how narrow wire channel cover fits into switch cover underneath hood. Remove range burners and sit on range facing switch cover for access to screws with small Phillips head screwdriver. Remove both back wire cover and switch cover screws. Remove covers. Remove plastic control knobs on front
... Read more by pulling straight off. Do not twist. With pliers or wrench remove two locking nuts. Light switch has three wires. Fan switch has four. Note wire colors and corresponding numbered slots on back of switch. Using end of large paper clip push into wire slot behind wire to loosen spring tension and carefully pull wire straight out. Do all wires in one switch at a time. Keep wire end straight and insert into correct numbered slot on new switch. Do not overtighten locking nuts upon reassembly. Replace knobs. Screw switch cover back on and then narrow wire cover. Turn circuit breaker on. Test new switches.
I just want to say thanks to this site for making access to these parts and self repairs. So easy. This was a great experience so self fulfilling and I saved a ton of money. Thank you .
Range Hood light switch was broken off at the screw thread that comes through the housing.
Cut the power to the unit by turning off the breaker on the panel. Then pulled off the knob for the light switch. From under the inside of the hood I used a Phillips head screw driver to remove the two metal screws securing the wire housing cover plate. This gave access to the broken switch. Sliding a very small straight slot screwdrive
... Read morer in the small slot beside the wire in the broken switch housing, this releases the wire and you pull it out. I did it one at a time, inserting the wire in the corresponding spot in the new switch so no mixups. Put the switch through the housing put on the retaining nut (gently so as not to break the plastic thread) and put the housing back, and the knob on, and presto! It's fixed!
Read less
1 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
★
Customer Reviews
Average Rating:
(1 Review)
5.0
★★★★★
★★★★★
Filter By Rating:
5★
1
4★
0
3★
0
2★
0
1★
0
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Kerry H - July 31, 2020
Verified Purchase
Range hood light switch
Part was delivered as promised and fit the repair perfectly. Works well after install.
Model Compatibility
This part works with the following models:
Fix Number: FIX953546
Manufacturer Part Number: WB24X10130
Item is in stock and will ship today if your order is placed before 4:00 PM Eastern Standard Time.
If your order is placed after 4:00 PM EST, the in stock items will ship on the next business day.
On Order
Item is not in stock and usually ships 3-5 business days from the time you place your order.
Special Order
Item is not in stock and usually ships 10-15 business days from the time you place your order.
NLA - No Longer Available
This item is no longer being made by the manufacturer, and cannot be added to your shopping cart.
✖
Mail-In Recycling Rebate
Some of the parts we sell are eligible for mail-in rebates since we can recycle them. We will display any applicable rebates in your shopping cart. To redeem your rebate, contact Customer Service after you have received your part.