Models
>
JV347H1WW
JV347H1WW General Electric Range Hood
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for JV347H1WW
Viewing 2 of 2Manuals & Guides for JV347H1WW
Click to downloadKeep searches simple, eg. "belt" or "pump".
In Stock
$19.82
This part is the replacement fan for your range hood. It is made of white plastic and is approximately 7 inches in diameter. The fan blade helps to dissipate smoke and smells from your range. The main...
In Stock
$14.40
This is the replacement fan switch for your range hood. When you turn the knob to turn the range fan on, the fan switch is actuated. If your fan will not turn on when the knob is turned, you most like...
In Stock
$12.98
This is the replacement light switch for your range. It comes with the actual switch, and the hex nut that goes with it. The switch is approximately 1 ¼ inches by 1 ¼ inches, and the hex nut is approx...
In Stock
In Stock
$32.88
This metallic vent hood filter collects grease particles in the air from cooking.
In Stock
In Stock
In Stock
In Stock
On Order
Special Order
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Helen J. from Landisburg, PA
- Parts Used:
- WB02X10700
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Replace grease and oder filter
To replace a filter, on my range, i just pull down on the old ,and push up tp place the new one in. the were no screws ,to take out. I would like to say, that the time it took , to place my order and recive it was great. i could not be more pleased . i will be in touch, again, whenever, i need a part ! thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from FLORENCE, NJ
- Parts Used:
- WB24X10130
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
The plastic part of the switch that screws into the hex nut broke off.
First, unplug the range hood, then remove the switch cover plate, held by two Phillips screws. Remove the switch knob and the hex nut on the front of the hood.(In my case, the hex nut had snapped off with the threaded part of the switch in it.) Then gently pull the switch away from the hood and write down which color wire (black, yellow,
... Read more
white) connects to which receptacle on the switch. The receptacles on the rear of the switch are marked L,1,2 and 3. 3 is left blank. Snip the wires from the switch, getting as close to the body of the switch as possible. Pulling them from the push-in receptacles doesn't work. Using a wire stripper, strip off about 1/2 inch of the wire insulation. Twist the exposed wires tightly and insert into the appropriate receptacles so that no bare wire shows. Insert the face of the switch into the hole on the hood so that the threaded portion protrudes. Using the hex nut provided, tighten snugly with an adjustable wrench. Do not over-tighten. Reattach the knob. Most of this repair went quickly and smoothly, but, despite repeated efforts, the threaded portion of the new switch did not fit through the original hole in the hood. As a result, I used a drill to enlarge the hole. The result was satisfactory but the new switch is not seated as well as the original. The knob does not line up exactly in the On, Off, Nite Light positions.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marsha from Jacksonville, FL
- Parts Used:
- WB02X10700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Really old filthy filter
Popped out the old one and inserted the new one. Very quick and easy, less than 1 minute. I was very impressed with the delivery of my new filter from PartSelect. It arrived the very next day...that was simply amazing to me.
Was this instruction helpful to you?
Thank you for voting!