OEM Ridgid Tile Saw Parts & Accessories

Wrench

$8.75

Fix Number: FIX10074928
Manufacturer Part Number: 0101010313

This is a genuine OEM approved replacement part used on Ryobi table saws. This wrench allows you to secure or remove a saw blade. Angular profile of this item makes tightening/loosening the arbor nut easy. This wrench is made from metal and it is sold individually.

Brush

$6.51

Fix Number: FIX16235992
Manufacturer Part Number: 089006017092

Designed for use with select Ridgid and Ryobi tools, this OEM approved replacement Brush fits a variety of models. To see if this part will fit your tool, please see the "Model Cross Reference List" below. This brush is made out of a durable Carbon alloy, has a lead wire attached to it, and its primary purpose is to conduct electrical current from the stationary wires to the moving parts of your tool. Brushes are one of the most commonly replaced power tool parts because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common cause of intermittent motor function, reduced electric braking, and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. Brushes are sold individually, and might also be known as Carbon Brushes or Motor Brushes. It is recommended to replace both brushes, even if only one is worn.

Installation Instructions

rich from WILLOW GROVE, PA

blade was making bad noise, and not spinning properly

Removed motor housing, arm, handle, spring and replaced. Found that gear and pinion were both stripped. Poor quality metal used in both. Read more...

ASSEMBLY CARBON BRUSH

$6.51

Fix Number: FIX18693574
Manufacturer Part Number: 291131002

This is a single OEM brush assembly with the leads, wire, and spring included. The brush holder is sold separately. Carbon brushes are known to wear from normal use of the tool, so it is important to consistently inspect and replace them as instructed by the manufacturer. It is also advisable to replace both brushes at the same time even if only one appears worn. For this quick and easy repair you will need a screwdriver. Disconnect the tool, remove the brush caps, remove worn brushes. Insert the new OEM brush assembly and secure the brush cap.

Installation Instructions

John from MACOMB, MI

Bad motor

Electrical and complete breakdown of saw. Plastic fan was shipped with missing blades. Started up out of balance. Did not solve problem. Used lithium grease as a last resort. Nice bon fire. Will be buying a new one Read more...

RIP FENCE ASSEMBLY INC KEY NOS

$54.83

Fix Number: FIX18688146
Manufacturer Part Number: 089041047709

Tile Saw Ball Bearing

$6.51

Fix Number: FIX9995584
Manufacturer Part Number: 671498001

Rip Fence Assembly

$18.49

★★★★★

1 Review

Fix Number: FIX16236325
Manufacturer Part Number: 089040002702

Carbon Brush

$6.51

Fix Number: FIX16235687
Manufacturer Part Number: 080015001641

This is a genuine OEM sourced replacement part designed for use with Ryobi saws. This assembly includes one (1) carbon brush with a lead wire and a spring attached. Please note brush holder is sold separately. Carbon brushes are a commonly replaced part on power tools. Due to normal use and friction brushes will gradually wear down and will require replacement. It is advised to replace both brushes at the same type. You would need a screwdriver to complete this job. • Make sure the unit is unplugged • First remove the cover • Take our old brushes and replace them with the new ones • Secure the cover and test the tool

Elevating Shaft (3/8-16 X 137

$6.51

★★★★★

1 Review

Fix Number: FIX10077070
Manufacturer Part Number: 089037007042

It is a genuine item that is supplied directly from the original equipment manufacturer for use with Ryobi table saws. This is an identical replacement for a missing or worn elevating shaft that was originally installed on a new unit, please make sure to refer to the appropriate diagrams of your unit for the correct location and application of this component. Keep in mind this high-quality item is made of durable metal and is sold individually.

RUBBER NOZZLE ASSEMBLY

$6.51

Fix Number: FIX18687433
Manufacturer Part Number: 089038001073

This is a manufacturer sourced replacement part used on some Ridgid tile saws. This part is made out of rubber. It helps to deliver water to the cutting wheel. It maximizes water efficiency and provides easy maintenance. Note that when installing nozzle, the hole must be pointing towards the saw. One (1) rubber nozzle is included per order.

REAR SPLASH GUARD

$5.95

Fix Number: FIX18687435
Manufacturer Part Number: 089038001076

This rear splash guard is an original part from the Ridgid manufacturer. This part is constructed of durable plastic. The splash guard is compatible with the R4040 Tile Saw and the R4040S Tile Saw. This item is secured onto the inner blade guard, and has been designed to minimize splash. A screwdriver is necessary for the installation. Rear splash guard is sold individually.

Ridgid Tile Saw Parts

Popular Ridgid Tile Saw Parts

Installation Instructions

Installation Instructions

Ridgid Tile Saw Appliance Types

Related Ridgid Tile Saw Parts

Popular Ridgid Tile Saw Models

Ridgid Tile Saw Parts

Start With Your Model Number

Popular Ridgid Tile Saw Parts

Installation Instructions

Installation Instructions

Ridgid Tile Saw Appliance Types

Related Ridgid Tile Saw Parts

Popular Ridgid Tile Saw Models