OEM Makita Reciprocating Saw Parts & Accessories

Shoe

$13.94

Fix Number: FIX10140526
Manufacturer Part Number: 163451-9

This reciprocating saw shoe provides a stable contact point against the work surface, helping guide cuts for improved accuracy and control while reducing vibration during use. Made from durable metal, it measures approximately 1.60 × 3.13 × 1.60 inches and features an adjustable design that allows you to control cutting depth and extend blade life. Replacing a worn or damaged shoe helps restore smooth operation, precise cutting performance, and overall tool stability.

Hex Head Bolt

$5.95

Fix Number: FIX10145400
Manufacturer Part Number: 266090-5

This is a Genuine OEM Makita replacement part, this part is sold individually. It is part of the blade clamping system for the specific Makita Reciprocating Saws. Only use the properly sized Hex Tool to tighten and loosen this bolt. Make sure the bolt is tight but not overtightened.

Driving Sleeve Guide

$6.55

Fix Number: FIX10150577
Manufacturer Part Number: 417791-0

This is an authentic OEM sourced replacement part designed for use with Makita reciprocating saws. This part helps securing the sleeve inside the tool. This part is made out of plastic and it is sold individually.

Brush Holder Cap

$6.51

Fix Number: FIX10153362
Manufacturer Part Number: 643750-0

This is a Genuine OEM replacement part used on Makita Power Tools. This item is made out of Plastic and it is Sold Individually. The purpose of the Brush Cap is to retain the Brushes in the Brush Holders. This Brush Cap has external threads that thread into the housing of the tool. Be careful when removing and replacing these, they have a tendency to break.

Carbon Brush Set

$10.36

Fix Number: FIX10156663
Manufacturer Part Number: CB441

This is a set of two carbon brushes. The carbon brushes should be checked on a regular basis. If they have worn down to the limit mark, it is time for a replacement. Both carbon brushes need to be replaced at the same time. For this repair use your screwdriver to detach the brush holder caps, remove the old carbon brushes, and insert the new ones. Fasten the new carbon brushes to the holder caps. To break in the new carbon brushes, run the tool with no load for about one minute.

Hex Head Bolt

$6.51

Fix Number: FIX10145304
Manufacturer Part Number: 265910-0

This is a genuine manufacturer approved replacement bolt designed for use with Makita reciprocating saw. It is used to secure the blade guide to the slider. This bolt is made out of metal and it is sold individually. Requires a hex key/allen wrench to install or remove this bolt.

Carbon Brush Set

$16.59

Fix Number: FIX10156649
Manufacturer Part Number: CB303

The carbon brush is used on a variety of tools and are commonly replaced because they wear out easily with time and use. If your brush is worn out it can affect the motor from working properly and reduce electric braking. Tip: to check if the brush is worn out, inspect the wire lead for cracks, burns and other damage. Refer to the diagram provided by the manufacturer for further installation instructions. *Please note: This part is sold individually. This assembly includes a carbon brush, spring and holder.

Ball Bearing 6001ddw

$25.93

Fix Number: FIX10141560
Manufacturer Part Number: 211131-2

This is an authentic part made by original manufacturer. This bearing is compatible with various Makita power tools. A bearing serves to separate and buffer moving parts. It also keeps the moving parts in position while still allowing them to move/turn as needed. As a high-wear part, bearings are often replaced. This item sold individually. Washers and retainers sold separately.

Insulation Cover

$26.83

Fix Number: FIX10151243
Manufacturer Part Number: 421904-7

This is an original Makita replacement part manufactured for use with reciprocating saws. The rubberized insulation cover provides a grip over the gear case. This insulation cover is available as an individual replacement part.

Cord Guard

$6.51

★★★★★

1 Review

Fix Number: FIX10153919
Manufacturer Part Number: 682503-2

• This cord guard is a genuine Makita replacement part and is sold individually. • Cord guards, also called cord protectors, are designed to slide onto your cord and fit securely at the end, where it's firm rubber will protect the base of the cord from getting bent and pinched, which can expose the wires and become a safety hazard. • This cord guard will fit cords for the tools listed under the "Compatible Tools" listing. It is not guaranteed to fit any other cords.

Makita Reciprocating Saw Parts

Popular Makita Reciprocating Saw Parts

Makita Reciprocating Saw Appliance Types

Related Makita Reciprocating Saw Parts

Popular Makita Reciprocating Saw Models

Makita Reciprocating Saw Parts

Start With Your Model Number

Popular Makita Reciprocating Saw Parts

Makita Reciprocating Saw Appliance Types

Related Makita Reciprocating Saw Parts

Popular Makita Reciprocating Saw Models