Models
>
JR3000V
JR3000V Makita Reciprocating Saw
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Diagrams for JR3000V
Viewing 1 of 1
Keep searches simple, eg. "belt" or "pump".
$32.12
This is a power cord, and it is used with several power tools. It is made of a thick rubber that is tough, and insulated for a long life. It has two 18 gauge wires, and is 8 feet long. When removing y...
In Stock
Order now and your part arrives by Aug 13
$12.74
If your motor is running poorly, running intermittently, it is likely in need of new carbon brushes. This part includes a set of two carbon brushes with wire leads and brush springs attached. Changing...
In Stock
Order now and your part arrives by Aug 13
$6.51
This is a cord guard, also known as a strain reliever, for your power tools. Power tool cords go through a lot of stress during usage, and this part is designed to remove some of that stress from the ...
In Stock
Order now and your part arrives by Aug 13
This is a genuine Makita replacement part, it is sold individually. It is part of the blade holding assembly for the reciprocating saws shown below. It is threaded into the Blade Clamp, then on the op...
No Longer Available
$5.95
This is a Genuine OEM Makita replacement part, this part is sold individually. It is part of the blade clamping system for the specific Makita Reciprocating Saws. Only use the properly sized Hex Tool ...
Special Order
$15.55
This is genuine Makita replacement part, it is sold individually. This is part of the reciprocating blade holding assembly for the tools listed below. By looking at the parts diagrams of those tools y...
In Stock
Order now and your part arrives by Aug 13
$22.67
Included in Part Number 516306-1. rnThis Ball Bearing is sealed on both sides. This genuine Makita replacement part is sold individually. rnrn • Ball bearings minimize friction between rotating par...
In Stock
Order now and your part arrives by Aug 13
Genuine Makita replacement part, this item is sold individually. The part number 256701-0 is part of the blade clamp system on the Makita JR3000V Type 2.It was used to secure the blade clamp block to ...
No Longer Available
$48.89
This is a Trigger type switch that has internal terminals and a locking mechanism. This genuine Makita replacement part is sold individually. Switches are commonly replaced parts in power tools. A s...
Special Order
$6.51
This manufacturer sourced replacement pin is made out rubber and it is sold individually. It acts as a cushion/spacer in a variety of Makita power tools. This is a standard piece of hardware and it ha...
In Stock
Order now and your part arrives by Aug 13
$6.51
This item is a genuine Makita part that has been sourced from the original manufacturer to be used with trimmers, circular saws, sanders, routers, nailers, reciprocating saws, laminate trimmers, and p...
In Stock
Order now and your part arrives by Aug 13
This #163258-3 Makita reciprocating saw shoe assembly will replace a worn or broken saw shoe. It is a genuine Makita replacement part. This shoe assembly will fit the Makita tools listed below. The...
No Longer Available
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Bruce from HILLSBORO, OR
- Parts Used:
- 664064-4
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
Old power cord frayed at the grommet entering the drill casing
Did not do repair as replacement part did not match description on partselect website. The grommet is not part of the replacement that was sent. Order #22962198
Email sent (11/16/2023) to partselect.com has gone unanswered
Thanks?
Email sent (11/16/2023) to partselect.com has gone unanswered
Thanks?
Was this instruction helpful to you?
Thank you for voting!