OEM Makita Miter Saw Parts & Accessories

Switch Button

$6.51

Fix Number: FIX10149734
Manufacturer Part Number: 411478-6

This is a single authentic switch activator button. Miter saws have a lockout mechanism on the switch, which stops the tool from being turned on by accident. The lockout is released by pushing on the switch button. The switch button can sometimes break or get lost and will need to be replaced. This is a very easy repair that does not require any tools. The switch button is secured with a plastic locking tab and can be removed by pulling it from the housing. To install the new switch activator button, position it in the housing and press it down until you hear a click.

Power Tool Power Cord

$33.76

★★★★★

1 Review

Fix Number: FIX10153842
Manufacturer Part Number: 664265-4

This power cord is for power tools. Unplug the power tool before installing this part. Wear work gloves to protect your hands.

Kerf Board

$6.44

Fix Number: FIX10150815
Manufacturer Part Number: 419222-5

This is a plastic kerf board (or kerf plate) for a saw. It has two screw holes to attach it to your equipment. This kerf board is sold individually, however two are required. This part is sourced directly from the manufacturer. The kerf board is designed to ensure a smooth cut, however using the incorrect kerf board or a damaged one could cause rough edges on the material being cut.

Carbon Brush Set Cb-203

$21.19

Fix Number: FIX10156645
Manufacturer Part Number: CB203

This part includes two carbon brushes with the wire leads and brush springs attached. In order for your motor to run at peak performance, it is imperative that the carbon brushes are well-maintained. The carbon brushes are needed to conduct electricity to the armature through the commutator. Over time these brushes wear down due to the constant rubbing. They should be regularly inspected to ensure your equipment continues to run smoothly. This repair should only take a few minutes.

Carbon Brush Set

$10.36

Fix Number: FIX10156663
Manufacturer Part Number: CB441

This is a set of two carbon brushes. The carbon brushes should be checked on a regular basis. If they have worn down to the limit mark, it is time for a replacement. Both carbon brushes need to be replaced at the same time. For this repair use your screwdriver to detach the brush holder caps, remove the old carbon brushes, and insert the new ones. Fasten the new carbon brushes to the holder caps. To break in the new carbon brushes, run the tool with no load for about one minute.

Press Plate

$6.51

Fix Number: FIX10156963
Manufacturer Part Number: JM23100023

This is an authentic Makita replacement part that has been sourced from the original manufactured to be used with miter saws. The hard plastic thumb plate is used to actuate the table lock bracket when changing the tables miter angle. This item is available as an individual replacement part.

Kerf Board

$6.63

Fix Number: FIX10151726
Manufacturer Part Number: 451013-8

This is an authentic manufacturer sourced replacement part used on Makita compound miter saws. Kerf boards (also called kerf plates) are used to prevent excessive splintering, resulting in cleaner cuts. Using the wrong kerf board for your tool can give a rough edge to the material you're cutting. This part is made out of plastic and it is sold individually. Screws that attach this part are sold separately.

Cord Guard

$6.51

★★★★★

1 Review

Fix Number: FIX10153921
Manufacturer Part Number: 682505-8

This cord guard or strain reliever prevents cord damage by covering the last portion of a cord before entering a tool. This provides extra support and rigidness. The cord fits garden and lawn equipment. With use, the cord guard can break down and your cord is left unprotected, in this case it is best to replace the guard. Refer to the diagram provided by the manufacturer for installation instructions.

Installation Instructions

John from Hancock, MI

Did not come with grinding disc guard

While unit was unplugged I screwed clamp of guard around grinder. Read more...

Carbon Brush Set

$16.59

Fix Number: FIX10156641
Manufacturer Part Number: CB154

This is a genuine Makita replacement part that includes two carbon brushes with wire leads attached. Carbon brushes are essential components in power tools and are among the most commonly replaced parts due to regular wear from friction. Over time, worn brushes can cause a motor to run poorly, operate intermittently, or lose electric braking power. Replacing them can often restore your tool’s performance. A worn brush may appear cracked, pitted, burned, or worn down near the wire lead. It’s always best to replace both brushes at the same time, even if only one shows signs of wear. When installing new brushes, be sure to inspect the armature for any damage such as burns or cracks, which could indicate more serious motor issues.

Kerf Board

$9.83

Fix Number: FIX10150110
Manufacturer Part Number: 416001-2

Kerf boards (also called kerf plates) are used to prevent excessive splintering, resulting in cleaner cuts. Using the wrong kerf board for your tool can give a rough edge to the material you're cutting.

Makita Miter Saw Parts

Popular Makita Miter Saw Parts

Installation Instructions

Makita Miter Saw Appliance Types

Popular Makita Miter Saw Models

Makita Miter Saw Parts

Start With Your Model Number

Popular Makita Miter Saw Parts

Installation Instructions

Makita Miter Saw Appliance Types

Popular Makita Miter Saw Models