OEM Ryobi Sander Polisher Parts & Accessories

Hook And Loop Backing Pad

$9.66

Fix Number: FIX10075791
Manufacturer Part Number: 030157001018

This sander pad is compatible with the Ryobi random orbit sander listed below. It is genuine Ryobi replacement part. The pad features a durable foam body attached to a hard plastic backing plate. It is a five inch diameter pad with a hook-and-loop style underside for use with Hook and Loop type sandpaper. This pad has eight vacuum holes. Hook and Loop sandpaper has become very popular over the past few years, because of the ease of changing sandpaper grits when needed.

Platen Assembly

$6.15

Fix Number: FIX10075990
Manufacturer Part Number: 039066005054

This is a genuine OEM replacement part designed for use with Ryobi Sander. This assembly consists of Plastic Platen with Metal Springs, Foam Pad with Metal Backing Plate and a Dust Shield. This is the part of the sander that holds the Sandpaper. Please note, it does not include the bearing. To replace this Platen Assembly you would need a Phillips Head Screwdriver. • Remove the 4 Screws holding old Platen • Take off the old Platen by pulling it off the Bearing • Press new Platen on the Bearing • Attach the new Assembly using the 4 Screws

Watch the install video

Brush Assembly (2 Required For

$6.25

Fix Number: FIX10076078
Manufacturer Part Number: 039143005002

This replacement brush assembly is an authentic OEM part that is specially made for Ryobi sanders. Carbon brushes are one of the most commonly replaced power tool components, through friction and regular use they will gradually wear away eventually requiring replacement. This assembly includes one carbon brush in a plastic holder with a metal wire terminal. To complete this repair you will need a screwdriver, it is highly advised to replace both brushes at the same time.

Watch the install video

Brake

$6.25

Fix Number: FIX10075790
Manufacturer Part Number: 030157001017

This brake is a genuine Ryobi replacement part. It is commonly used in random orbit sanders. It is made of rubber and sold individually. A screwdriver is needed for replacement. To replace this part: 1. Remove the backing pad by removing the four screws. 2. Remove the top cap by extracting the retaining screws. 3. Remove the switch trigger by lifting it out of the unit. 4. Remove the retaining screws from the motor housing. Then separate the two halves and top of the housing with a screwdriver. 5. Remove the old break pad from the unit and replace it with the new pad by aligning the tabs with the grooves. 6. Reassemble the unit.

Bearing Cap Assembly

$6.25

Fix Number: FIX10075786
Manufacturer Part Number: 030157001013

This is an authentic OEM part. The Ryobi bearing cap assembly is composed of metal and plastic, and has been designed for use with RS290 Random Orbit Sander and the RS290G Random Orbit Sander. This sealed bearing component helps to secure the fan and the brake. The bearing cap assembly helps devices to run smooth and cut down on internal friction. A screwdriver is needed in the removal and replacement. This part is sold individually.

Ball Bearing (6000lu)

$6.15

Fix Number: FIX9868401
Manufacturer Part Number: 039176001012

It is an original manufacturer supplied replacement item and is sold individually. This ball bearing is sealed on both sides. Ball bearings are made to reduce friction between two rotating parts. Because they experience constant pressure they would need to be checked and replaced periodically to ensure top performance. Please check diagrams for correct location and application of this bearing.

Tile Saw Ball Bearing

$6.25

Fix Number: FIX9995584
Manufacturer Part Number: 671498001

Conversion Pad

$6.25

Fix Number: FIX10085217
Manufacturer Part Number: 900482001

Genuine Ryobi replacement part, this item is sold individually. The purpose of the 900482001 Conversion Pad is to convert the PSA (Adhesive Sand Paper) Pad to a Hook and Loop Pad. All you need to do is remove the adhesive paper from the back of the Conversion Pad and place it on the PSA Pad. Then you will have a Hook and Loop Pad.

5 DISC ASSEMBLY W/ H&L

$9.06

★★★★★

1 Review

Fix Number: FIX18693700
Manufacturer Part Number: 300527002

This is an authentic 5-inch sanding pad assembly for a sander. It provides support for hook and loop sandpaper. This part is prone to deteriorate, especially if too much pressure is applied to the sander while in use. This creates too much heat, which wears the sanding pad much quicker. For this simple repair, unfasten the four screws attaching the pad to the sander, and fasten the new pad in its place. This OEM pad assembly is sold individually.

Installation Instructions

Michael from EL PASO, TX

replaced hook and loop pad

Removed the 4 screws and replaced. Read more...

Pad Assembly

$6.25

★★★★★

1 Review

Fix Number: FIX10075988
Manufacturer Part Number: 039066005051

This is a genuine Ryobi replacement part. The pad is what the sandpaper is attached to by the clamps on the platen assembly. It includes the metal backing on the back of the pad. To remove the pad, simply remove the four phillips head screws that attach the pad to the platen.

Ryobi Sander Polisher Parts

Popular Ryobi Sander Polisher Parts

Installation Instructions

Ryobi Sander Polisher Appliance Types

Related Ryobi Sander Polisher Parts

Popular Ryobi Sander Polisher Models

Ryobi Sander Polisher Parts

Start With Your Model Number

Popular Ryobi Sander Polisher Parts

Installation Instructions

Ryobi Sander Polisher Appliance Types

Related Ryobi Sander Polisher Parts

Popular Ryobi Sander Polisher Models