OEM Black and Decker Belt or Drum Sander Parts & Accessories

DUST BAG ASSY

$12.60

Fix Number: FIX12487158
Manufacturer Part Number: A23158

This is an OEM dust bag for your sander, and it is sold as an individual part. The dust bag connects to the sander to help control the dust created while sanding. This part includes the cloth bag and wire frame that secures it. There is also a zipper located at the bottom of the bag, which is used to easily empty it after each use. Over time the bag can wear or the zipper may damage. This is a quick, easy, and tool-free repair that you can do yourself. This dust bag is connected to the sander with a spring clamp. Press the two halves of the spring clamp together and pull it to remove. Take your new dust bag, pinch the clamp together and place the bag over the opening.

BELT

$8.42

Fix Number: FIX18981445
Manufacturer Part Number: 491937-00

This is a manufacturer-approved belt for a sander, and it is sold as an individual part. This rubber belt is 16-inches by 3/8-inches and has 80 teeth. It is located underneath the belt cover and is placed around the segmented drive pulley and driven pulley. It is what drives the sanding belt and sanding disk. It is common for the cogs to wear down over time, the belt can also crack, break, and start to fray along the edges. If the sander is overloaded this can speed up the wear of the belt. For this repair you will need to remove the belt cover, and then you will line up the belt onto the pulleys.

Watch the install video

Power Cord (10-foot)

$24.41

Fix Number: FIX10169874
Manufacturer Part Number: 330072-97

This cord is a genuine DeWalt replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 2 Prongs • 2 Wires • 18 Gauge • 10 Feet Long

KNOB

$6.51

Fix Number: FIX12502235
Manufacturer Part Number: 897159

Genuine OEM replacement part used on Belt Sanders. it is Sold Individually. This part consists of a Plastic Knob with a Metal Threaded Shaft. This part in conjunction with a Spring will allow you to Adjust Belt Tracking by turning the Knob in either direction until the edge of the belt is even with the outer edge of the rear rubber-covered pulley. Replacing this part is very easy and it does not require any additional tools.

Watch the install video

SS/A HANDLE SET

$16.04

Fix Number: FIX12467035
Manufacturer Part Number: A03070

This is a Genuine OEM Sourced replacement part designed for use with Sanders and Band Saws. This item is made out of Plastic and it is Sold Individually. It includes Two (2) Pieces of the Knob. Please note the Screw used to secure this Knob is Sold Separately.

Belt

$9.72

Fix Number: FIX10180446
Manufacturer Part Number: 587263-00

This is a genuine OEM sourced replacement belt used on Bosch sanders. This is the main drive belt for the unit. This item is made out of rubber and it is sold individually. It is recommended to replace these belts every 6 months to ensure optimum performance. You would need a screwdriver to complete a repair. • Remove the belt cover • Replace the old belt with the new one • Secure the housing

Drive Roller

$16.02

Fix Number: FIX10185595
Manufacturer Part Number: 90545358

This is a genuine manufacturer-approved component which is designed for DeWalt and Black and Decker sanders. It is a high-quality replacement for a missing or a damaged drive roller that was installed on a new unit. The part is an important component of the mechanism that rotates the sanding belt. Refer to the appropriate diagram for your model to ensure the correct repair procedure. Note, this high-quality drive roller is made of a durable material and is sold individually. A screwdriver and pliers will be needed to perform this repair.

Watch the install video

BEARING,NEEDLE

$21.78

Fix Number: FIX12475150
Manufacturer Part Number: 804211

This is a genuine replacement steel bearing from original manufacturer. It is commonly used in Porter Cable and Black & Decker belt sanders. Bearings are parts which separate metal parts to ease in movement and reduce friction. They also stabilize and prevent incorrect direction/tilt during movement. These high-wear parts are replaced regularly. This part is sold individually. Washers etc. sold separately.

Carbon Brush and Spring

$9.77

★★★★★

1 Review

Fix Number: FIX12522806
Manufacturer Part Number: N031635

This part includes one carbon brush with a wire lead and brush spring attached. A poorly running motor is often due to worn brushes, which is why they are such a common repair in power tools. Due to the constant friction they are under, they will wear over time, and will need to be replaced. If upon inspection you notice the carbon brush is burnt or otherwise damaged, you will also want to check the condition of the armature, as this might suggest a larger problem with the motor.

Dust Bag Assembly

$17.35

Fix Number: FIX10180509
Manufacturer Part Number: 588562-00

This dust bag assembly is a genuine OEM replacement part, it is not an aftermarket imitation. This high quality item is made for use with Dewalt and Black and Decker sanders. The purpose of this bag is to collect the dust picked up by sander. It is made with strong fabric material with a plastic collar. It has a zipper for quick and easy clean up. Please note, one dust bag assembly is included per order. No tools needed to replace this part.

Black and Decker Belt or Drum Sander Parts

Popular Black and Decker Belt or Drum Sander Parts

Black and Decker Belt or Drum Sander Appliance Types

Popular Black and Decker Belt or Drum Sander Models

Black and Decker Belt or Drum Sander Parts

Start With Your Model Number

Popular Black and Decker Belt or Drum Sander Parts

Black and Decker Belt or Drum Sander Appliance Types

Popular Black and Decker Belt or Drum Sander Models