Shaper Parts

115V CORD

$22.94

Fix Number: FIX18986769
Manufacturer Part Number: 825713

This is a Porter Cable replacement part designed for use with many power tools. The 115V cord is constructed of metal wiring encased in plastic and durable rubber. The cord is designed to connect the device to electricity once plugged into an outlet. This part is sold individually. Soldering tools are needed to make the proper replacement. Please refer to manual and diagrams for specific repair instructions.

Handle

$32.95

Fix Number: FIX10322076
Manufacturer Part Number: 406030330001S

This handle is an OEM direct from Delta. The handle is made for use with a variety of power tools. The metal handle allows the operator to make the needed adjustments for projects. This handle is sold individually. A screwdriver, pliers, socket and wrench set are often required for the proper installation. Please refer to the specific manual for further repair instructions.

Bearing (for Recent Models Onl

$26.35

Fix Number: FIX10329672
Manufacturer Part Number: 920040107273

It is an authentic item that is supplied directly from original equipment manufacturer for use with Delta power equipment. This replacement bearing helps to secure the spindle while allowing it to rotate with minimal friction. For correct location and use of this item make sure to check appropriate diagrams of your equipment. Please note this durable metal bearing is sold individually.

Washer, 1" Spindle .087 – Part Number: 3840004

Washer, 1" Spindle .087&#3

$7.60

Fix Number: FIX10458956
Manufacturer Part Number: 3840004

This is an OEM part sourced directly from the manufacturer. The spindle washer is designed for use in Powermatic shapers. This part is made of metal, and is used in securing the spindle assembly. You will require a wrench when replacing this part. This item is sold individually.

Roll Pin

$6.51

Fix Number: FIX10328508
Manufacturer Part Number: 905010102732S

This is an authentic Delta replacement part sourced directly from the manufacturer. The roll pin is found in several different machines from Delta. This part is made of metal, and is put to different uses in the machine, depending on model. Please refer to the parts diagram to be sure of ordering the correct part. This part is sold individually.

Roller

$66.96

Fix Number: FIX10316720
Manufacturer Part Number: 1340360

The roller attaches to the cover with the washer and the cap screw. This part is an OEM from Delta for use in stock feeder shapers. It is made out of metal and hard rubber and will need to be replaced if it stops turning. An allen wrench will be needed to replace this wheel. Keep in mind that this part is available as an individual replacement even though multiple rollers may be needed.

Key

$11.79

Fix Number: FIX10329808
Manufacturer Part Number: 927030102650S

The key attaches to the shaft and is made out of metal. This item is available individually. This is a genuine replacement part sourced from the original manufacturer for use with saws, drills, jointers, and shapers made by Delta. When replacing this part a set of pliers might be required during the installation process. It will require replacing if it becomes bent or broken.

Starter 27-66-72 5hp 3ph Nhd #

$264.44

Fix Number: FIX10463241
Manufacturer Part Number: 6816295

The starter attaches to the shaper stand. This part is available individually. It is an authentic OEM sourced item which is specially produced for use with Powermatic shapers and table saws. A screwdriver may be required to replace this part. It is made of plastic and metal and will require replacing if it becomes broken.

On/off Switch (3hp 1ph. 230 Vo

$267.57

Fix Number: FIX10463239
Manufacturer Part Number: 6816292

This switch controls power to 3 HP, 1-phase machines and includes overload protection. Replace if the machine won’t start or shows electrical issues. Always disconnect power before installation.

Flat Washer

$9.85

Fix Number: FIX10467508
Manufacturer Part Number: TS-0680031

This is a flat washer, and it used with various power tools. The flat washer is made entirely of metal, and has an outer diameter of 1 inch. This part provides a secure seal between connected parts. Generally positioned under a nut or the head of a bolt. This washer is sold individually.

Popular Shaper Parts

Shaper Brands

Related Shaper Parts

Popular Shaper Models

Shaper Parts

Start With Your Model Number

Popular Shaper Parts

Shaper Brands

Related Shaper Parts

Popular Shaper Models