OEM Ryobi Router Parts & Accessories

Starting Pin

$5.95

Fix Number: FIX16237467
Manufacturer Part Number: 089220105035

The starting pin attaches to the insert plate and is made of plastic. This part is available as an individual replacement. During replacement, it may require a set of pliers to help install this item correctly. It will need to be replaced if it becomes bent or broken. This is a genuine OEM sourced part which is specially designed for use with Ryobi routers.

Tile Saw Ball Bearing

$6.51

Fix Number: FIX9995584
Manufacturer Part Number: 671498001

Collet 1/4 Inch

$6.51

Fix Number: FIX16755887
Manufacturer Part Number: 690045003

This genuine component is supplied directly from the original equipment manufacturer for use with Ryobi power tools. The collet allows a user to secure a bit. Note, it is for using bits with 1/4

Carbon Brush W/spring Assembly

$6.51

Fix Number: FIX10080339
Manufacturer Part Number: 290069107

This high quality replacement brush assembly is specially designed for use with Ryobi routers. It is a genuine OEM sourced item, not an aftermarket equivalent. Motor brushes allow electricity to flow to the motor's spinning armature. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems. It is advised to replace both brushes at the same time. This assembly includes (1) carbon brush in a metal brush holder with a lead wire and a spring attached. You would need a screwdriver to complete this job. • Unplug the tool • Remove the housing • Remove the old brush • Secure the new one in place • Reassemble and test the tool

Circular Saw Lock Nut (M5)

$6.51

Fix Number: FIX10083854
Manufacturer Part Number: 670974003

This is a genuine component which is supplied directly from the original equipment manufacturer for Ryobi and Ridgid equipment. It is a standard hardware which may have multiple applications, please make sure to refer to the appropriate diagrams of your model for the correct location and use of this hardware. Keep in mind this high-quality lock nut is made of durable metal and is sold individually.

Bearing Ball 608zz

$6.40

Fix Number: FIX11858686
Manufacturer Part Number: 680141022

Genuine Manufacturer Approved replacement part used on a variety of Power Tools. This Ball Bearing has multiple applications depending on your tool. This part is made out of Metal and it is Sold Individually. Ball Bearings are used to reduce friction between rotating parts. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. This reduces wear on the tool and allows it to run smoothly. Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement. To replace this Bearing you would need a Screwdriver and a Set of Wrenches.

Knob Large Lock

$6.51

Fix Number: FIX16237451
Manufacturer Part Number: 089220105019

It is a genuine item that is supplied directly from the original equipment manufacturer for Ryobi router tables. It is an identical replacement for a missing or a damaged knob that was installed on a new unit, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this part. Keep in mind this high-quality hardware is made of durable plastic and is sold individually.

Subbase-Square

$6.51

Fix Number: FIX16349653
Manufacturer Part Number: 519234001

This authentic item is supplied directly from the original equipment manufacturer for use with Ridgid trimrouters. When replacing this part a screwdriver may be needed. Over time the subbase-square may break and will need to be replaced. This item is sold individually and is made out of plastic.

Small Lock Knob W/shoulder

$6.40

Fix Number: FIX16237452
Manufacturer Part Number: 089220105020

An authentic manufacturer-supplied replacement part that is specially made for use with Ryobi routing tables. This is one of the special small lock knobs for the fence assembly, for the correct location and use please make sure to check appropriate diagrams of your model. It is a high-quality hardware which is made of durable plastic and it is sold individually.

Carbon Brush Assembly

$6.51

Fix Number: FIX10080335
Manufacturer Part Number: 290069048

This is a genuine manufacturer approved replacement brush. It is specially produced for Ryobi routers. Includes one (1) carbon brush with lead wire, spring and a metal holder attached. Please note, most tools use two brushes. It is recommended to replace both brushes at the same time to ensure top performance. Replacing this carbon brush is a simple task that should only require a screwdriver to complete this job. • First make sure the tool is unplugged • Remove the brush caps • Remove the old brush • Secure the new brush • Reassemble and test your tool

Installation Instructions

John from HARPSWELL, ME

Replacement brushes did not fit.

I removed old brushes, and seeing they did not match, I made modifications to the new set.
This was done by rotating the brush set 90*, and beveling the edges to match the previous set. This took a little finesse using a knife and sandpaper to fit the tolerances.
All said and done with the new brushes in place, it ran!
I’ve yet to see the endurance yet. Read more...

Ryobi Router Parts

Popular Ryobi Router Parts

Installation Instructions

Ryobi Router Appliance Types

Related Ryobi Router Parts

Popular Ryobi Router Models

Ryobi Router Parts

Start With Your Model Number

Popular Ryobi Router Parts

Installation Instructions

Ryobi Router Appliance Types

Related Ryobi Router Parts

Popular Ryobi Router Models