OEM Makita Demolition Hammer Parts & Accessories

O Ring 28

$6.51

Fix Number: FIX10141868
Manufacturer Part Number: 213415-4

This is a genuine replacement part designed for use with Makita power tools. This o-ring provides an air-tight seal for the connected parts. Please make sure to check appropriate diagrams for location and use of this item. Over time o-rings will shrink, become brittle and crack allowing for air leaks. At that time they should be replaced. It is made out of rubber and it is sold individually.

Ball Bearing

$23.30

Fix Number: FIX10141535
Manufacturer Part Number: 211066-7

This is a Ball Bearing that is sealed on both sides. This is a genuine Makita replacement part that is sold individually. rnrn • Ball bearings minimize friction between 2 parts in your tool that would otherwise spin and rub against each other. The balls or rollers take the load and spin, distributing the weight evenly while the minimal contact area of the balls reduce friction. This reduces wear on the tool and allows it to run smoothly. rn • Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

Brush Holder Cap

$6.51

Fix Number: FIX10153356
Manufacturer Part Number: 643700-5

This is a manufacturer sourced replacement part designed for use with Makita power tools. It helps to secure the brush in the housing. This screw-in cap is made of hard plastic and it is sold individually and measures 7-18 HM 1500. To replace it you would need a flat-head screwdriver.

Carbon Brush Set

$13.26

Fix Number: FIX11885917
Manufacturer Part Number: CB351

This is a Genuine Manufacturer Sourced replacement part used on Makita Rotary Hammers. Includes Two (2) Carbon Brushes with Lead Wires attached. Please note Brush Holders and Springs are Sold Separately. Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. It is recommended to replace both brushes at the same time. You would need a Screwdriver and Pliers to complete this job.

Carbon Brush Set

$15.09

Fix Number: FIX10156644
Manufacturer Part Number: CB175

This is a set of two carbon brushes with the lead wire attached. Please note that the holder and spring are sold separately. Some models will display a red indicator light when the carbon brushes are worn and require servicing. Poor motor performance or a tool that will not turn on are also strong indications that the carbon brushes may require replacement. To get access to the carbon brushes you will need a hex key/Allen wrench to open the housing.

Brush Holder Unit

$16.86

Fix Number: FIX10153125
Manufacturer Part Number: 632D00-2

This replacement brush holder unit is a high quality item that is supplied by original equipment manufacturer for use with Makita demolition hammers. Its purpose is to secure carbon brushes around the armature to maintain stable contact. This item is a complete assembly which includes the plastic ring, two metal brush holder with attached lead wires, please note the carbon brushes themselves are sold separately. Keep in mind this brush holder unit is sold individually.

Hammer Grease

$9.16

Fix Number: FIX10156274
Manufacturer Part Number: A-90582

This genuine manufacturer approved hammer grease is sold individually. This petroleum based grease is designed for use with Makita hammers. It helps to lubricate the system allowing for easy movement and protecting parts from usual wear.

Cord Guard

$6.51

★★★★★

1 Review

Fix Number: FIX10153921
Manufacturer Part Number: 682505-8

This cord guard or strain reliever prevents cord damage by covering the last portion of a cord before entering a tool. This provides extra support and rigidness. The cord fits garden and lawn equipment. With use, the cord guard can break down and your cord is left unprotected, in this case it is best to replace the guard. Refer to the diagram provided by the manufacturer for installation instructions.

Installation Instructions

John from Hancock, MI

Did not come with grinding disc guard

While unit was unplugged I screwed clamp of guard around grinder. Read more...

Switch

$36.25

Fix Number: FIX10153680
Manufacturer Part Number: 651922-3

This replacement switch is specially made for use on Makita power tools. Switches are a commonly replaced item in power tools. They play a key role by controlling on/off function of a tool. Because switches use mechanical internals, they will degrade and wear out over time, eventually requiring replacement. To replace this switch you would need a screwdriver. • First make sure the tools is not plugged in • Remove housing screws • Disconnect wires from the old switch • Remove it from the housing • Place the new switch in the housing • Reconnect wires to it • Reassemble and test the unit

Carbon Brush Set

$35.36

Fix Number: FIX10156646
Manufacturer Part Number: CB204

This is a set of two OEM carbon brushes with wire leads and brush springs. To ensure your motor is running efficiently, it is important to continually inspect the carbon brushes, as they are a common wear part. If they are damaged this will greatly affect the performance of the motor. If burns or cracks are present, it is advised to inspect the armature as well.

Makita Demolition Hammer Parts

Popular Makita Demolition Hammer Parts

Installation Instructions

Makita Demolition Hammer Appliance Types

Related Makita Demolition Hammer Parts

Popular Makita Demolition Hammer Models

Makita Demolition Hammer Parts

Start With Your Model Number

Popular Makita Demolition Hammer Parts

Installation Instructions

Makita Demolition Hammer Appliance Types

Related Makita Demolition Hammer Parts

Popular Makita Demolition Hammer Models