Biscuit Joiner Parts

Dust Bag

$36.45

Fix Number: FIX10166198
Manufacturer Part Number: 147734-06

This is an authentic item that is supplied directly from the original equipment manufacturer for Craftsman Plate Joiners. The Dust bag collects the dust created when operating the saw. The dust bag is made out of fabric and is sold individually. The adapter is sold separately. No tools need to install this part.

Plane Bearing

$13.17

Fix Number: FIX10142070
Manufacturer Part Number: 214251-1

This is an Authentic OEM Approved replacement part designed for use with Makita Planers/Jointers. This part is made out of Metal and it is Sold Separately. This part helps to secure the Roller and allows it to spin smoothly. To replace this part you would need Retaining Ring Pliers, Screwdriver and a Set of Wrenches.

Adaptor

$6.51

Fix Number: FIX10166215
Manufacturer Part Number: 147794-00

This genuine OEM dust adapter in your jointer plate allows you to attach various sizes of vacuum hoses to it for direct dust pick-up. It is part of the dust collection system, you can easily check if the dust adapter is damaged by visually inspecting it for signs of wear or deformations. If you find that it has become loose, fails to create a tight seal, or does not fit the vacuum hose sizes properly, it needs to be replaced. To remove the adapter, firmly pull it out from your machine. When installing the new adapter, insert it into the dust exhaust port on the right side at the rear of the base assembly until it clicks into place. Please keep in mind that this is sold separately from the dust attachment elbow and the dust bag.

Handle

$8.89

Fix Number: FIX10166214
Manufacturer Part Number: 147793-00

It is an authentic original manufacturer supplied replacement part that is specially designed for Dewalt and Black and Decker jointers. This handle provides user with a safe and comfortable grip for operating the tool. It is made from high quality plastic and it is sold individually, please note the hardware to secure it is sold separately.

Switch Ps-10

$19.53

Fix Number: FIX10153534
Manufacturer Part Number: 650621-4

This switch is a genuine Makita replacement switch. This shaft lock switch prevents spindle rotation when installing/removing accessories. This piece is sold individually. A screwdriver is all that is needed for this quick repair.

LEFT PIVOT

$12.23

Fix Number: FIX18987938
Manufacturer Part Number: 903370

Genuine Manufacturer Sourced replacement part used on a some Porter Cable Jointers. This part is made out of Plastic and it is Sold Individually. This part uses Two (2) Screws to attach it to the unit, they are Sold Separately.

Terminal

$6.51

Fix Number: FIX10173813
Manufacturer Part Number: 464228-00

This is a terminal for your power tools. The terminal attaches to the cord of your machine, and then to the electrical connection on the tool. Through this connection, the electricity travels from the wall, through the terminal, and into your machine. The most common reason for needing to replace this part, is if your machine is plugged in but not turning on.

Installation Instructions

John from SPRINGVILLE, CA

Old worn cord shorting out.

Remove the four screws and carefully separate the casing at the trigger handle. Disconnect the terminals by lifting the switch slightly, just enough to remove the inside terminal. Needle nose pliers will make it easier to remove the terminals. Slip the cord protector over the new cord. Cut the two new wires to the proper length. I measured the old connectors for proper fit. Strip a half inch off the insulation, carefully crimp and solder the wires to each terminal, reconnect the terminals, reposition the cord protector, align and snap the casing back together, and replace the four screws. Plug it in and test for proper operation. Read more...

Washer,Spring

$6.51

Fix Number: FIX10170704
Manufacturer Part Number: 385946-00

Lock Nut Wrench

$14.14

Fix Number: FIX10154215
Manufacturer Part Number: 782401-1

Genuine Makita replacement part used on Angle Grinders and Plate Joiners. This Wrench allows you to secure a Cutter Blade or a Grinding Wheel to the tool. Angular profile of this item makes tightening/loosening the lock nut easy, as it stands off from the disc. This wrench is made from Metal and it is Sold Individually. Please be aware that this wrench will not fit the 5/8" lock nut. You need a separate wrench for the 5/8" lock nut.

Grip

$8.21

Fix Number: FIX10151898
Manufacturer Part Number: 453218-6

This is an authentic replacement part manufactured for use with Makita plate joiners. The grip attaches to the front of the joiner and is used to stability for making accurate cuts. The grip is sold as an individual replacement part.

Popular Biscuit Joiner Parts

Installation Instructions

Biscuit Joiner Brands

Related Biscuit Joiner Parts

Popular Biscuit Joiner Models

Biscuit Joiner Parts

Start With Your Model Number

Popular Biscuit Joiner Parts

Installation Instructions

Biscuit Joiner Brands

Related Biscuit Joiner Parts

Popular Biscuit Joiner Models