Hammer Brushes

Popular Hammer Brushes

Carbon Brush Set
$10.28
In Stock
Fix Number
FIX10156652
Manufacturer Part Number
CB325
Genuine Makita replacement part. Set of 2 Carbon Brushes with wire lead attached. • Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.
Carbon Brush
$6.51
In Stock
Fix Number
FIX10122113
Manufacturer Part Number
22-16-0275
This is a carbon brush, it is also known as a motor brush, and it is used with various power tools and equipment. The brush transfers electric currents to the motor. Your motor brush is an extremely common replacement part. It is considered a wear part, because the constant friction will wear it down. If you are experiencing a poor running motor, you will need to replace this part. New brushes will restore your motors electric braking. We recommend also inspecting your armature for damaging cracks or burns, this can indicate a larger problem in your motor that will require attention.
Carbon Brush Set
$16.59
In Stock
Fix Number
FIX10156656
Manufacturer Part Number
CB407
This set comes with two carbon brushes with wire leads and brush strings attached. If your motor is not running efficiently or is operating intermittently, this is a common sign of worn brushes. Due to the friction they are constantly under, they will wear over time, and will start to appear cracked, pitted, or burnt if not replaced regularly. We recommend also taking a look at the armature to ensure it is not damaged. This brush set is compatible with multiple model types, so it is best to consult your user manual for repair instructions.
Carbon Brush Set
$13.26
In Stock
Fix Number
FIX11885917
Manufacturer Part Number
CB351
This is a Genuine Manufacturer Sourced replacement part used on Makita Rotary Hammers. Includes Two (2) Carbon Brushes with Lead Wires attached. Please note Brush Holders and Springs are Sold Separately. Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. It is recommended to replace both brushes at the same time. You would need a Screwdriver and Pliers to complete this job.
Carbon Brush Set
$10.36
In Stock
Fix Number
FIX10156663
Manufacturer Part Number
CB441
This is a set of two carbon brushes. The carbon brushes should be checked on a regular basis. If they have worn down to the limit mark, it is time for a replacement. Both carbon brushes need to be replaced at the same time. For this repair use your screwdriver to detach the brush holder caps, remove the old carbon brushes, and insert the new ones. Fasten the new carbon brushes to the holder caps. To break in the new carbon brushes, run the tool with no load for about one minute.
★★★★★
★★★★★
1 Review
Fix Number
FIX10187386
Manufacturer Part Number
N031214
This part contains two carbon brushes and holder sets. Carbon brushes are a routine maintenance task, as they are prone to wear due friction. Worn brushes are the most common reason for a motor that is not running properly or at all. In general, this is a pretty easy repair, but keep in mind that instructions can vary slightly depending on the model. To access the brushes, you will need to remove the housing of the tool and the brushes will be located inside the holders close to the motor.
Brush Box
$13.49
In Stock
★★★★★
★★★★★
1 Review
Fix Number
FIX10180814
Manufacturer Part Number
603754-01
The brush box assembly is used on a variety of cordless tools and tools. This assembly includes a carbon brush, spring and holder. Carbon brushes are commonly replaced because they wear out easily with friction. If your brush is worn out it disrupt the function of the motor and reduce electric braking. Tip: to check if the brush is worn out, inspect the wire lead for cracks, burns and other damage. Replacing the brush can restore the motor and its functions. Refer to the manual provided by the manufacturer for further installation instructions. *Please note: This part is sold individually.
Brush Kit ( Includes Both Brus
$35.77
In Stock
Fix Number
FIX10165412
Manufacturer Part Number
1005550-03
This carbon brush kit is a genuine OEM sourced item, it is not an aftermarket imitation. It is specially designed for Dewalt demolition hammers. This set includes (2) carbon brushes with lead wires attached. It is advised to replace both brushes at the same time. You will need a screwdriver to complete this repair.
BRUSH SET
$23.60
On Order
Fix Number
FIX19504867
Manufacturer Part Number
1617014145
BRUSH SET
$28.88
In Stock
Fix Number
FIX19504833
Manufacturer Part Number
1617000A50

Hammer Brush Brands