DeWALT Hammer Brushes

★★★★★

★★★★★

1 Review

Fix Number

FIX10187386

Manufacturer Part Number

N031214

This part contains two carbon brushes and holder sets. Carbon brushes are a routine maintenance task, as they are prone to wear due friction. Worn brushes are the most common reason for a motor that is not running properly or at all. In general, this is a pretty easy repair, but keep in mind that instructions can vary slightly depending on the model. To access the brushes, you will need to remove the housing of the tool and the brushes will be located inside the holders close to the motor.

★★★★★

★★★★★

1 Review

Fix Number

FIX10180814

Manufacturer Part Number

603754-01

The brush box assembly is used on a variety of cordless tools and tools. This assembly includes a carbon brush, spring and holder. Carbon brushes are commonly replaced because they wear out easily with friction. If your brush is worn out it disrupt the function of the motor and reduce electric braking. Tip: to check if the brush is worn out, inspect the wire lead for cracks, burns and other damage. Replacing the brush can restore the motor and its functions. Refer to the manual provided by the manufacturer for further installation instructions. *Please note: This part is sold individually.

Fix Number

FIX10165412

Manufacturer Part Number

1005550-03

This carbon brush kit is a genuine OEM sourced item, it is not an aftermarket imitation. It is specially designed for Dewalt demolition hammers. This set includes (2) carbon brushes with lead wires attached. It is advised to replace both brushes at the same time. You will need a screwdriver to complete this repair.

Fix Number

FIX10167174

Manufacturer Part Number

176949-17

This is an OEM Manufacturer Sourced replacement part used on certain Hammer Drills. Includes One (1) Carbon Brush with wire lead attached. Please note: this brush is sold individually and most tools would use Two of these carbon brushes. It is always best to replace both brushes, even if only one is worn. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

Fix Number

FIX10187774

Manufacturer Part Number

N047286

This is a genuine manufacturer-sourced replacement brush set which is specially designed for use with Dewalt demolition hammers. Carbon brushes are one of the most commonly replaced power tool components, they maintain physical contact with an armature helping to conduct electric current. Over time brushes will wear away eventually requiring replacement to maintain peak performance. It is a high-quality brush set which includes two durable carbon brushes with attached lead wires, please note brush holders are sold separately.

Fix Number

FIX12525793

Manufacturer Part Number

N418050

Fix Number

FIX10169034

Manufacturer Part Number

323660-00

Includes 1 Carbon Brush with wire lead attached. Genuine DeWalt replacement part. • Worn brushes are often the cause behind a poorly running motor. • Replacing brushes can fix an intermittently operating motor. • New brushes can restore a motor's electric braking. Carbon motor brushes are one of the most commonly replaced power tool parts. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. When replacing carbon brushes be sure to also inspect your armature for burns, cracks, or other damage which are indication of a larger motor problem.

Fix Number

FIX10187777

Manufacturer Part Number

N047425

This manufacturer supplied replacement brush set is designed for Dewalt rotary hammers. This assembly includes two (2) carbon brushes with lead wires attached. Please note brush holders are sold separately. Due to prolonged contact with an armature brushes will gradually wear down and will require replacement. It is advised to replace both brushes at the same type. You would need a screwdriver to complete this job. • Make sure the unit is unplugged • Remove screws from the housing to gain access to the armature and brushes • Remove old brushes and secure the new ones in brush holders • Re-assemble and test the tool

Fix Number

FIX10174249

Manufacturer Part Number

489257-00

This is an original DeWalt replacement part manufactured for use with demolition hammers. Brushes will wear out over time because of constant contact with the armature which rotates inside the electric motor. Signs of worn brushes are sparking, trouble starting, and diminished performance. Replacing worn brushes is part of normal maintenance, and this pair of brushes are sold as individual pairs.

Fix Number

FIX10174503

Manufacturer Part Number

493511-00