DeWALT Hammer Drill Brushes

★★★★★

★★★★★

1 Review

Fix Number

FIX10187386

Manufacturer Part Number

N031214

This part contains two carbon brushes and holder sets. Carbon brushes are a routine maintenance task, as they are prone to wear due friction. Worn brushes are the most common reason for a motor that is not running properly or at all. In general, this is a pretty easy repair, but keep in mind that instructions can vary slightly depending on the model. To access the brushes, you will need to remove the housing of the tool and the brushes will be located inside the holders close to the motor.

★★★★★

★★★★★

1 Review

Fix Number

FIX10180814

Manufacturer Part Number

603754-01

The brush box assembly is used on a variety of cordless tools and tools. This assembly includes a carbon brush, spring and holder. Carbon brushes are commonly replaced because they wear out easily with friction. If your brush is worn out it disrupt the function of the motor and reduce electric braking. Tip: to check if the brush is worn out, inspect the wire lead for cracks, burns and other damage. Replacing the brush can restore the motor and its functions. Refer to the manual provided by the manufacturer for further installation instructions. *Please note: This part is sold individually.

Fix Number

FIX10188928

Manufacturer Part Number

N198492

This is an Genuine Manufacturer Approved replacement part designed for Dewalt Drills. This item is made out of Carbon and Metal. This item includes One (1) Carbon Brushe with a Lead Wire attached. Please note Brush Holder and Spring is Sold Separately. Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. It is recommended to replace both brushes at the same time. You would need a Screwdriver and Pliers to complete this job.

Fix Number

FIX10165412

Manufacturer Part Number

1005550-03

This carbon brush kit is a genuine OEM sourced item, it is not an aftermarket imitation. It is specially designed for Dewalt demolition hammers. This set includes (2) carbon brushes with lead wires attached. It is advised to replace both brushes at the same time. You will need a screwdriver to complete this repair.

★★★★★

★★★★★

1 Review

Fix Number

FIX10173420

Manufacturer Part Number

445860-00

This is a brush spring and it is used in a variety of power tools. The spring applies force to the motor brush inside the motor. This will keep the brush tight along the armature. If the brush has worn down it will create heat, and the spring will lose tension. If this happens, both parts will have to be replaced.

Fix Number

FIX10188792

Manufacturer Part Number

N157123

Genuine Dewalt replacement part, this item is sold individually. This part contains the Brush Holder,Brush Spring and Brush. It is used on all of the tools listed below. It is always best to replace both brushes, even if only one is worn. Worn brushes frequently are the cause behind a motor running poorly. Replacing brushes can fix a motor that's operating intermittently. New brushes can restore a motor's electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

Fix Number

FIX10167174

Manufacturer Part Number

176949-17

This is an OEM Manufacturer Sourced replacement part used on certain Hammer Drills. Includes One (1) Carbon Brush with wire lead attached. Please note: this brush is sold individually and most tools would use Two of these carbon brushes. It is always best to replace both brushes, even if only one is worn. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

★★★★★

★★★★★

1 Review

Fix Number

FIX10188793

Manufacturer Part Number

N157129

Genuine Dewalt replacement part, this item is sold individually. This part contains the Brush Holder,Brush Spring and Brush. It is used on all of the tools listed below. It is always best to replace both brushes, even if only one is worn. Worn brushes frequently are the cause behind a motor running poorly. Replacing brushes can fix a motor that's operating intermittently. New brushes can restore a motor's electric braking. Carbon brushes are one of the most commonly replaced power tool parts. This is because carbon brushes are wear items, meaning that through friction and use they will gradually wear away until they need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, be sure to inspect your armature for burns, cracks, or other damage which can indicate larger motor problems.

Fix Number

FIX12525856

Manufacturer Part Number

N443604

Fix Number

FIX10187774

Manufacturer Part Number

N047286

This is a genuine manufacturer-sourced replacement brush set which is specially designed for use with Dewalt demolition hammers. Carbon brushes are one of the most commonly replaced power tool components, they maintain physical contact with an armature helping to conduct electric current. Over time brushes will wear away eventually requiring replacement to maintain peak performance. It is a high-quality brush set which includes two durable carbon brushes with attached lead wires, please note brush holders are sold separately.