Electric Drill Seals and Gaskets

Popular Electric Drill Seals and Gaskets

Seal
$43.66
In Stock
Fix Number
FIX10132361
Manufacturer Part Number
45-06-0635
This is a Genuine Manufacturer Sourced replacement part designed for use with Milwaukee Drills. This part is made out of Metal and Rubber Material. This part provides a seal for Water Swivel Housing. There are Two (2) of these Seals on each end of Water Swivel Housing. Please note this item is Sold Individually. To complete this repair you would need a Screwdriver and Pliers.
Base Gasket
$41.34
In Stock
Fix Number
FIX10130114
Manufacturer Part Number
43-44-0605
It is an OEM part that is specially made for use with Milwaukee large base dymorigs. This gasket is utilized to provide a tight seal for the base. Over time gaskets tend to wear out and may begin to crack causing leaks and eventually requiring a replacement. Note, this high-quality component is made of durable rubber material and is sold individually. Check the appropriate diagram for your model to ensure the exact location and the correct replacement procedure. No special tools should be needed to perform this repair.
O-ring
$6.25
In Stock
Fix Number
FIX10165195
Manufacturer Part Number
034158-00
O-rings are designed to contain thousands of pounds of pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-Ring failure, such as pressure, friction, temperature or chemicals. The most common are: • <u>Extrusion and Nibbling</u> - O-ring has ragged, tattered edges. These are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • <u>Abrasion</u> - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that is too rough, contains grit or is too smooth to allow lubrication. • <u>Over Compression </u> - O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • <u>Heat Hardening</u> - O-ring has a pitted or cracked surface, and often is flattened on both sides. Caused by temperature exceeding o-ring capacity. • <u>Weather/Ozone Cracking</u> - O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching causes similar cracking.
O-ring
$6.25
In Stock
Fix Number
FIX10126919
Manufacturer Part Number
34-40-1100
This replacement part is supplied directly from the original equipment manufacturer for use with Milwaukee drills. It is one of the special o-rings which are utilized to provide an air-tight seal for the spindle, please refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this durable part is made of high-quality rubber and is sold individually.
Trostel Seal
$52.20
In Stock
Fix Number
FIX10132292
Manufacturer Part Number
45-06-0050
This authentic OEM trostel seal is found in the water swivel housing of your electric drill. It helps to create a watertight barrier that keeps water away from the internal components of the drill. The housing itself is designed to enable wet drilling tasks, with a water hose fitting that connects to the drill and delivers a controlled stream of water directly to the drilling area. You can determine if the seal needs replacement by inspecting it for signs of wear, damage, or deterioration. If you notice any water leakage from the swivel housing during use, the seal may be compromised and in need of replacement. You may also find visible cracks on it. To replace the seal, refer to your user manual for guidance on disassembling the drill to access the swivel housing. Once accessed, you can remove the old seal and install the new one. Keep in mind that the housing, as well as its associated components like the shut-off valve and water hose fitting, are sold separately from this replacement part.
O-ring
$6.25
In Stock
Fix Number
FIX10126934
Manufacturer Part Number
34-40-1350
This is an authentic manufacturer-approved replacement o-ring that is specially designed for use with Milwaukee drills presses. It helps to provide an air tight seal for the spindle. It is made of durable rubber material and it is sold individually, over time it may begin to deteriorate and crack eventually requiring replacement.
O-ring
$6.25
In Stock
Fix Number
FIX11929412
Manufacturer Part Number
N075339
O-rings are commonly utilized to provide a tight seal between connected components. Unfortunately, over time the material will wear out and it may begin to crack eventually requiring a replacement. Keep in mind this high-quality o-ring is made of durable rubber material and is sold as an individual item. It is a genuine item that is supplied by the original equipment manufacturer for use with DeWALT and Porter Cable impact drivers.
GASKET
$6.25
In Stock
Fix Number
FIX18705019
Manufacturer Part Number
902683001
O-ring
$6.25
On Order
Fix Number
FIX10126926
Manufacturer Part Number
34-40-1200
This is a genuine manufacturer sourced replacement part, it is commonly utilized on Milwaukee power tools. It helps to distribute the pressure evenly and provide an air-tight seal between connected pieces, please refer to the appropriate diagrams of your model for the correct location and application os this hardware. Over time the material may wear out and begin to crack eventually requiring a replacement. Keep in mind this high-quality rubber component is sold individually.
O Ring
$6.25
In Stock
Fix Number
FIX10188946
Manufacturer Part Number
N210233
This is an authentic manufacturer sourced replacement part designed for use with DeWALT and Black and Decker rotary demolition hammers. It helps to provide an air-tight seal for the cap, please make sure to refer to the appropriate diagrams of your model for the correct location and use of this hardware. It is made of high-quality rubber and it is sold individually, over time the material may wear out and crack eventually requiring replacement.

Electric Drill Seal or Gasket Brands