DeWALT Electric Drill Seals and Gaskets

DeWALT Appliance Parts

Popular DeWALT Electric Drill Seals and Gaskets

O-ring
$6.51
In Stock
Fix Number
FIX10165195
Manufacturer Part Number
034158-00
O-rings are designed to contain thousands of pounds of pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-Ring failure, such as pressure, friction, temperature or chemicals. The most common are: • <u>Extrusion and Nibbling</u> - O-ring has ragged, tattered edges. These are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • <u>Abrasion</u> - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that is too rough, contains grit or is too smooth to allow lubrication. • <u>Over Compression </u> - O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • <u>Heat Hardening</u> - O-ring has a pitted or cracked surface, and often is flattened on both sides. Caused by temperature exceeding o-ring capacity. • <u>Weather/Ozone Cracking</u> - O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching causes similar cracking.
O-ring
$6.51
In Stock
Fix Number
FIX11929412
Manufacturer Part Number
N075339
O-rings are commonly utilized to provide a tight seal between connected components. Unfortunately, over time the material will wear out and it may begin to crack eventually requiring a replacement. Keep in mind this high-quality o-ring is made of durable rubber material and is sold as an individual item. It is a genuine item that is supplied by the original equipment manufacturer for use with DeWALT and Porter Cable impact drivers.
O Ring
$6.51
In Stock
Fix Number
FIX10188946
Manufacturer Part Number
N210233
This is an authentic manufacturer sourced replacement part designed for use with DeWALT and Black and Decker rotary demolition hammers. It helps to provide an air-tight seal for the cap, please make sure to refer to the appropriate diagrams of your model for the correct location and use of this hardware. It is made of high-quality rubber and it is sold individually, over time the material may wear out and crack eventually requiring replacement.
Gasket
$6.51
In Stock
Fix Number
FIX10173732
Manufacturer Part Number
450485-00
This is an original replacement part sourced directly from the manufacturer. The gasket is commonly found in drills from DeWALT and Black & Decker. This part is made of flexible plastic, and is used to seal the connection between the gear case cover and the gear case. You will require a screwdriver when replacing this item. The gasket is sold as an individual replacement part.
Ring,o
$6.51
In Stock
Fix Number
FIX10169044
Manufacturer Part Number
323711-15
This is an original replacement part manufactured for use with rotary hammers. The special o-ring is commonly used to provide cushioning and spacing at the connection point between part assemblies. This o-ring is used with several different models of rotary hammers and the part application may vary depending on the model. The o-ring is sold as an individual replacement part, please see model diagram for part location.
Ring,o
$6.51
In Stock
Fix Number
FIX10169050
Manufacturer Part Number
323711-26
O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. Of the many causes for O-Ring failure, the most common among power tools are: • <u>Extrusion and Nibbling</u> - The O-ring has ragged, tattered edges. These are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • <u>Abrasion</u> - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that is too rough, contains grit or is too smooth to allow lubrication. • <u>Over Compression </u> - The O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • <u>Heat Hardening</u> - The O-ring has a pitted or cracked surface, and is often flattened on both sides. Caused by temperature exceeding o-ring capacity. • <u>Weather/Ozone Cracking</u> - The O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching (greater that 5%) causes similar cracking.
Seal
$6.51
On Order
Fix Number
FIX10184188
Manufacturer Part Number
696534-00
It is a genuine item that is supplied directly from the original equipment manufacturer for use with DeWALT and Black and Decker screwdrivers. This special component is utilized to provide an air-tight seal between connected parts, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind over time the material may wear out and crack eventually requiring a replacement. It is a high-quality seal which is made of durable material is sold individually.
Seal
$6.51
In Stock
Fix Number
FIX10169240
Manufacturer Part Number
325936-00
SEAL
$12.34
In Stock
Fix Number
FIX12508543
Manufacturer Part Number
N244259
Gasket
$5.36
Special Order
Fix Number
FIX10170757
Manufacturer Part Number
386422-00

Related DeWALT Electric Drill Parts