Black and Decker Electric Drill Power Cords

★★★★★

★★★★★

1 Review

Fix Number

FIX10169875

Manufacturer Part Number

330072-98

This power cord is used for power tools and some of the following tools: electric drills, reciprocating saws, jig saws, biscuit joiners, and routers. The power cord is made for double insulated tools and is a two-wire cord with two prongs, but it does not need a ground wire. If there are cuts in the cord insulation, intermittent power during operation, or damaged and bent prongs, then replacing the power cord will solve the problem. The tools needed for this repair are a Phillips screwdriver, small screwdriver, wire cutters/strippers, crimping tool, and terminal (ring or spade). Repair tip: During installation, remember that new cord wires must go correctly into wire terminals. Also, to avoid pinching when the tool case is put back into place, remember to route cord and wires in the right path.

★★★★★

★★★★★

3 Reviews

Fix Number

FIX10173396

Manufacturer Part Number

445338-00

This is a cord protector, also known as a strain relief, for your power tool. This part will slip into place at the end of your cord, snug against your power tool. The durable rubber will protect the base of your cord from being bent, pinched, or exposed. This part will eventually wear down and potentially crack or snap off, and exposed wire is a hazard. We recommend replacing the cord protector when damage is visible.

Fix Number

FIX10169655

Manufacturer Part Number

330005-01

This is a cord protector, but it is also called a strain relief, and it is used with multiple power tools. This part is made of firm rubber to protect the cords from being pulled out or exposed, which would be a safety hazard. Over time the strain relief can develop cracks and break into pieces. This part is black and 4 inches long. The smallest end has a diameter of 0.5 inches. When completing this repair tuck in all wires to avoid pinching.

Fix Number

FIX10169907

Manufacturer Part Number

330077-98

This cord is a genuine DeWalt replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 2 Prongs • 2 Wires • 18 Gauge • 8 Feet Long

Fix Number

FIX10169973

Manufacturer Part Number

36480-98

This cord is a genuine DeWalt replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 3 Prongs • 3 Wires • 18 Gauge • 10 Feet Long

Fix Number

FIX10169976

Manufacturer Part Number

36495-98

This cord is a genuine DeWalt replacement part and is sold individually. It is constructed with tough, thick outer rubber insulation for a long service life. Power Cord Specifications: • 3 Prongs • 3 Wires • 16 Gauge • 15 Feet Long

Fix Number

FIX10173549

Manufacturer Part Number

448557-98

This replacement 10 foot power cord is specially produced for Black and Decker and Dewalt power tools. It is designed to connect to a standard US outlet supplying power to the tool. Please note one rubber insulated cord is included per order, the cord protector is not included it is sold separately. To complete this repair you will need a screwdriver.

Fix Number

FIX10166291

Manufacturer Part Number

148809-00

This is a genuine OEM sourced replacement part designed for use with a variety of power tools. Cord guards, also called cord protectors, are designed to slide onto your cord and fit securely at the end, where it's firm rubber will protect the base of the cord from getting bent and pinched, which can expose the wires and become a safety hazard. It is made out of rubber and it is sold individually.

Fix Number

FIX10173377

Manufacturer Part Number

444518-98

This 10 ft. power cord is a genuine manufacturer sourced replacement part that is specially produced for Black and Decker and Dewalt power tools. It is used to supply electricity from a standard U.S. outlet to the tool. One durable rubber insulated cord is included per order, please note the cord sleeve protector is sold separately.

Fix Number

FIX10168984

Manufacturer Part Number

323091-01

This rubber piece is a genuine OEM part manufactured for DeWALT and Black & Decker. It is sold individually. A cord protector attaches at the point of connection between cord and power tool. It protects cord and wires from damage caused by stress, strain, and motion. This repair is fairly simple and requires just a screwdriver. A damaged cord must be replaced as well. Replacement cords are sold separately. • Unplug power tool • Remove the casing • Detach wires from tool • Slide cord protector onto cord • Reattach wires and casing • Test power tool