OEM Black and Decker Electric Drill Parts & Accessories

Carbon Brush

$6.88

Fix Number: FIX10167153
Manufacturer Part Number: 176846-04

This is a single OEM carbon brush. Two are needed to make a set, so if you require two, order accordingly. Carbon brushes are used to conduct electricity to the armature through its commutator. Brushes are a common wear part that will need to be replaced periodically due to consistent rubbing against the rotating commutator. Worn brushes can cause sparks around the commutator, which can also cause damage to the armature, which should also be inspected. If your electric motor is experiencing issues, the brushes should be one of the first things you check.

Carbon Brush With Spring

$10.77

Fix Number: FIX10173724
Manufacturer Part Number: 450374-12

This is a brush and spring for your power tools. This brush is sold individually, and two are needed for most power tools. We recommend replacing both brushes together for an even wear. When your brush wears down it will greatly affect your motor function by reducing the power and electric braking. When making this repair we recommend inspecting the armature for cracks or visible damage that would mean other motor problems. Carbon brushes are the most commonly replaced power tool part. This part is meant to wear out over time through the constant contact.

Clutch Assembly

$53.85

Fix Number: FIX10172536
Manufacturer Part Number: 429634-00

This is an authentic manufacturer approved replacement part designed for use with drills/screwdrivers. This clutch assembly is connected to the transmission and the shaft. Keeping an eye on equipment performance will determine when the clutch requires replacement. Includes part numbers 176842-00, 89210-00

Cord Protector

$7.89

★★★★★

3 Reviews

Fix Number: FIX10173396
Manufacturer Part Number: 445338-00

This is a cord protector, also known as a strain relief, for your power tool. This part will slip into place at the end of your cord, snug against your power tool. The durable rubber will protect the base of your cord from being bent, pinched, or exposed. This part will eventually wear down and potentially crack or snap off, and exposed wire is a hazard. We recommend replacing the cord protector when damage is visible.

Carbon Brush

$9.06

Fix Number: FIX10172207
Manufacturer Part Number: 400814-00

Genuine Dewalt/Black & Decker replacement part. includes 1 Carbon Brush with wire lead and brush spring attached. 2 Brushes are needed for the tools listed below. • Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.

Ball Bearing

$8.28

Fix Number: FIX10180907
Manufacturer Part Number: 605040-15

Genuine OEM sourced replacement part used on a variety of power tools. Ball bearings are used to reduce friction between rotating parts. Bearings experience constant wear when the tool is in operation, because of this they need to be periodically checked and replaced if needed. This part is made out of metal and it is sold individually. Included in part number 381004-00 spindle assembly.

CHARGER

$25.40

Fix Number: FIX18989568
Manufacturer Part Number: 90640340

Genuine Manufacturer Sourced replacement part used on some Black and Decker Power Tools. This item is sold individually. Purchasing a charger will be less expensive than buying a new tool. Please note that a weak or defective battery can damage the charger. Weak batteries are batteries with bad cells. These type of batteries will not hold a charge. It will send a message to the charger to keep charging. This will eventually cause the charger to overheat and potentially smoke.

Charger

$20.97

Fix Number: FIX17016372
Manufacturer Part Number: 90593303-01

This is a genuine Black and Decker replacement charger, sold individually. It’s designed to recharge the battery used in the cordless tools listed below. Over time, chargers can wear out or stop functioning properly. Replacing the charger is a cost-effective solution that can extend the life of your tools—often much less expensive than purchasing a brand-new unit.

Brush Spring

$6.51

★★★★★

1 Review

Fix Number: FIX10173420
Manufacturer Part Number: 445860-00

This is a brush spring and it is used in a variety of power tools. The spring applies force to the motor brush inside the motor. This will keep the brush tight along the armature. If the brush has worn down it will create heat, and the spring will lose tension. If this happens, both parts will have to be replaced.

Handle,spade

$13.87

Fix Number: FIX10182689
Manufacturer Part Number: 628037-00

This is an original replacement part manufactured for use with drills. This hardened plastic spade handle is secured at the back of the drill using a knob, which is available separately. The spade handle provides an additional grip option for heavy duty drills, please note the spade handle is sold individually.

Black and Decker Electric Drill Parts

Popular Black and Decker Electric Drill Parts

Black and Decker Electric Drill Appliance Types

Related Black and Decker Electric Drill Parts

Popular Black and Decker Electric Drill Models

Black and Decker Electric Drill Parts

Start With Your Model Number

Popular Black and Decker Electric Drill Parts

Black and Decker Electric Drill Appliance Types

Related Black and Decker Electric Drill Parts

Popular Black and Decker Electric Drill Models