Black and Decker Compressor Seals and Gaskets

★★★★★

★★★★★

1 Review

Fix Number

FIX9964140

Manufacturer Part Number

5140118-80

It is a genuine manufacturer sourced replacement part that is specially designed for Craftsman air compressors. This gasket provides an air-tight seal for the cylinder head assembly. Over time gaskets tend to get compressed, become brittle and crack eventually requiring replacement to maintain peak performance. It is made from durable, high quality composite material and it is sold individually.

Fix Number

FIX18991071

Manufacturer Part Number

AC-0781

This is a rubber O-ring for a compressor. It creates a seal for the tube as it enters the head. This part is sourced directly from the original manufacturer, ensuring it is the correct fit. It measures approximately 0.362 in inner diameter and 0.103 in outer diameter. Over time, the O-ring can begin to wear and should be replaced to maximize the power of your air compressor. Before you begin this repair, you will need to unplug the unit and bleed air from the tank.

★★★★★

★★★★★

2 Reviews

Fix Number

FIX12517182

Manufacturer Part Number

N017592SV

This is a valve plate for your compressor or generator. This part controls the air flow into the pump. When the air is pumped by the piston, it passes through the valve plate and into the compressor tank. The most common sign of a damaged valve is if your pressure is not building up in the tank. The reeds on the valve plate are usually the first thing to wear out. If you notice visible damage on the reeds you will need to replace this part. This valve includes the plate, and the lower gasket. The head gasket is sold individually.

★★★★★

★★★★★

2 Reviews

Fix Number

FIX12522478

Manufacturer Part Number

N044359

This is a tube seal used with various power tools. The seal prevents air from leaking out of your equipment. It is placed on the outlet tube, and connected to the head of the compressor. Note that this part is sold individually. If you are having trouble with your air pressure, you may need to replace this part.

Fix Number

FIX12513125

Manufacturer Part Number

ACG-45

O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. rnrnThere are many causes for O-Ring failure. The most common among power tools are: • <u>Extrusion and Nibbling</u> - The O-ring has ragged, tattered edges. These are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • <u>Abrasion</u> - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that it too rough, contains grit or is too smooth to allow lubrication. • <u>Over Compression </u> - The O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • <u>Heat Hardening</u> - The O-ring has a pitted or cracked surface, and is often flattened on both sides. Caused by temperature exceeding o-ring capacity. • <u>Weather/Ozone Cracking</u> - The O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching (greater that 5%) causes similar cracking.

Fix Number

FIX12543085

Manufacturer Part Number

Z-D24819

This is a manufacturer-approved head gasket for an air compressor, sold individually. It is designed to seal the valve plate to the cylinder head. If this gasket is damaged or worn, this can create an air leak from the head, which will make it so the compressor is no longer pressurizing the tank. For this repair you will need the following tools: Philips screwdriver, torx drivers, flat-blade screwdriver, long-nosed pliers, impact driver or socket wrench, and a torque wrench.

★★★★★

★★★★★

1 Review

Fix Number

FIX12523902

Manufacturer Part Number

SSG-8156

O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. There are many causes for O-Ring failure. The most common among power tools are: • <u>Extrusion and Nibbling</u> • The O-ring has ragged, tattered edges. These are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • <u>Abrasion</u> • One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that it too rough, contains grit or is too smooth to allow lubrication. • <u>Over Compression </u> • The O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • <u>Heat Hardening</u> • The O-ring has a pitted or cracked surface, and is often flattened on both sides. Caused by temperature exceeding o-ring capacity. • <u>Weather/Ozone Cracking</u> • The O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching (greater that 5%) causes similar cracking.

Fix Number

FIX12512459

Manufacturer Part Number

A03865

The gasket is sourced from the original manufacturer to ensure quality. This item is intended to be used with air compressors from Porter Cable, Black and Decker, and DeWalt. The gasket is used to seal the connection between the cylinder head and the body of the cylinder. This item is available as an individual replacement part.

★★★★★

★★★★★

1 Review

Fix Number

FIX18991725

Manufacturer Part Number

D30139

Genuine OEM replacement parts kit. This Gasket Kit is used to prevent air leaks in the compressors listed below. Over time the gaskets will become compressed or cracked and you will hear an air leak coming from the compressor. They will need to be replaced. This would be a good time to inspect all the other wear parts of the compressor.

Fix Number

FIX18982337

Manufacturer Part Number

5140118-79

This is a genuine Craftsman replacement gasket, it is supplied directly from the original equipment manufacturer for use with air compressors. It is the special component which helps to provide an air-tight seal for the cylinder head assembly, over time the gasket may wear out and crack eventually requiring a replacement to maintain peak performance. This high-quality part is made of durable composite material and it is sold individually.