DeWALT Chop Saw Brushes

Fix Number

FIX16687899

Manufacturer Part Number

N558583

This is a genuine Dewalt replacement part, it is sold individually. Worn brushes are often the cause of a poorly running motor • Replacing brushes can fix an intermittent motor • New brushes can restore a motor's electric braking Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.

Fix Number

FIX10173724

Manufacturer Part Number

450374-12

This is a brush and spring for your power tools. This brush is sold individually, and two are needed for most power tools. We recommend replacing both brushes together for an even wear. When your brush wears down it will greatly affect your motor function by reducing the power and electric braking. When making this repair we recommend inspecting the armature for cracks or visible damage that would mean other motor problems. Carbon brushes are the most commonly replaced power tool part. This part is meant to wear out over time through the constant contact.

Fix Number

FIX10182308

Manufacturer Part Number

622440-00

This is a genuine OEM approved replacement part designed for use with chop saws. This item holds carbon brush against the armature. It is made out of plastic with metal and it is sold individually. Please note carbon brushes are sold separately. To replace this assembly you would need a screwdriver and pliers. • First remove screws holding the cover together • Carefully remove two halves of the housing to gain access to armature and brush holder • Remove the screws holding brush holder to the trigger • Remove the armature assembly and the brush holder • Install the new brush holder, brushes and the armature • Reassemble and test your tool

★★★★★

★★★★★

1 Review

Fix Number

FIX10173420

Manufacturer Part Number

445860-00

This is a brush spring and it is used in a variety of power tools. The spring applies force to the motor brush inside the motor. This will keep the brush tight along the armature. If the brush has worn down it will create heat, and the spring will lose tension. If this happens, both parts will have to be replaced.

Fix Number

FIX10181326

Manufacturer Part Number

610126-00

Genuine OEM Dewalt replacement Carbon Brush and Holder Assembly. This brush comes complete with carbon brush, spring, and holder. Most brush replacement jobs will require the purchase of two of these brush assemblies. Carbon motor brushes are one of the most commonly replaced power tool components. Because carbon brushes are wear items, meaning that through friction and use they will gradually wear away, they will eventually require replacement. Worn brushes are common causes of intermittent motor function, reduced electric braking, and reduced motor power. A worn out brush will often be worn down near the wire lead and may be cracked, pitted, or burned. When replacing carbon brushes, be sure to also inspect your armature for burns, cracks, or other damage which indicates a larger motor problem.

Fix Number

FIX10170575

Manufacturer Part Number

384613-01

This part includes one carbon brush. Your tool will require two of these, and they should be replaced at the same time. Worn carbon brushes are the most likely reason that a motor is not performing as it should. The function of the carbon brushes are to conduct electricity to the armature. This is done through the commutator. Carbon brushes are constantly rubbing against the spinning commutator, and this is why they wear over time. For this simple repair, start by removing the motor cap. To replace the brush, remove the wire lead and tension spring, and pull the brush from the holder. To install the brush, place it into the holder, place the tension spring on the rear of the brush and reinstall the wire lead. The same thing will need to be done on the other side.

Fix Number

FIX10188019

Manufacturer Part Number

N077337

This is an authentic Dewalt carbon brush, not an aftermarket imitation. It is specially designed for use with angle grinders. Its function is to conduct electric current in power tools. This item includes (1) carbon brush with a lead wire attached. Please note, the brush box assembly is sold separately. It is advised to replace both brushes at the same type. You will need a screwdriver to replace this brush. • Make sure the unit is unplugged • Remove the housing • Take out the old brush • Secure the new brush • Reassemble and test the unit

Fix Number

FIX10188363

Manufacturer Part Number

N097997

This replacement carbon brush pair is specially made for a Dewalt chop saw. It is an authentic OEM sourced item, not an aftermarket imitation. This item includes (2) carbon brushes with lead wires and springs attached. You will need a screwdriver to complete this repair.

Fix Number

FIX16688330

Manufacturer Part Number

N593369

Fix Number

FIX10173430

Manufacturer Part Number

445861-36

This replacement brush is an authentic OEM item that is specially designed for use with Dewalt cut out tools. Carbon brushes play an important role in power tools by conducting electric current in the motor. This assembly includes one carbon brush with an attached lead wire, please note it is advised to replace both brushes at the same time. You will need a screwdriver to complete this repair job.